Anything FXR !!!

[CycleFreak]

Make or buy a heatshield that stands off the pipe. It'll still be warm, but not near as bad as just heat wrap.

[mrhammer2u]

Here's a sweet unmolested one in my neck of the woods. Not mine and I have no idea who this is. Just thought I would share since you don't see em this nice too often for sale.

http://newjersey.craigslist.org/mcy/5931793616.html

[FXR65]

Yep, worked just fine.

[CraiGORE]

113 FXR almost done
bulletproof drivetrain and lots of performance parts

[BluBeaSSt]

113 FXR almost done
bulletproof drivetrain and lots of performance parts

Looks killer!



On another topic, is there a good write up on how to align the motor in the frame?

[gorgeous]

I second this ^^^ I want to redo my motor mounts as well, hate paying people to do work for me that I can do myself. Seems like a total pain in the ass though.

[CraiGORE]

from another forum:


1. Elevate bike just enough to take the weight off the suspension front and rear.

2. Take 2 straight edges. I like to use square aluminum tubing it is relatively cheap and as long as it's eyeball straight it'll work. Use a couple of big C clamps or bungees and attach the straight edges to each side of the rear wheel. Note: sometimes blocking these from the bottom helps cause if you over clamp the rails you will distort them.

3. Make sure the front wheel is straight (torqueing down the triple clamp so the front end stays in place helps at this point) put your inclinometer on the rear disc and then the front disc. The manual says they should be the same within 2 degrees. If they are good then great if not then adjust the top link accordingly. Leveling the frame doesn't hurt but it really isn't needed. If the wheels are in vertical alignment then the frame has to match unless something seriously F'd up at the swingarm (I have seen it happen).

4. Using a ruler measure from the edge of the front tire to the inside of the straight edges on both sides if the front wheel. If it is not centered then loosen the lock nuts on the link and adjust until centered.

5. Check all the fasteners you loosened during the adjustment and torque the lock nuts on the links and that's it, your done, GO FOR A RIDE!

[Spade115]

Looks damn good man, I was talking to the wife about dropping an ultima 127 in my FXR heeheehee

[CraiGORE]

Looks damn good man, I was talking to the wife about dropping an ultima 127 in my FXR heeheehee

do it!

[FXRYouGoingToTheMallLater]

Was getting a nasty vibration on my '89 FXRS w/ front wheel and handlebars dancing like crazy at idle. I replaced the front motor mount and that cured the dancing wheel and bars, but I'm still getting a ton of vibration through the seat. Happens at 2,500 RPMs in any gear. Vibrates so bad that my balls fall asleep after a 15 min ride. Any ideas on what it could be? Top stabilizer link, maybe?

[Lou333]

113 FXR almost done
bulletproof drivetrain and lots of performance parts

Real nice. What fork brace you using?

[CraiGORE]

Real nice. What fork brace you using?

thanks
I got it off this forum a few years ago I think it's a vtwin copy of a screamin eagle brace. nothing fancy but does the job. noticed a huge improvement when I bolted it on

[hmmrstrike]

I have an FXLR. I cut my fender mounts off and I wanna put them back on. Does anyone know where I can find the dimensions for these frames. I know that Harley likes to guard their stuff pretty heavily but I really need a hand here.

Thanks

[ecir45]

I have an FXLR. I cut my fender mounts off and I wanna put them back on. Does anyone know where I can find the dimensions for these frames. I know that Harley likes to guard their stuff pretty heavily but I really need a hand here.

Thanks

Easiest would be bolt some struts to the shock mount and use the holes in the strut as a jig to line up the fab piece you want to add back.

[xMPRx]

Finished up the mini floor boards for the fxr.

[IMG][/IMG]


[IMG][/IMG]