Bad-Boy 92 inch 1952 Pan

[Dragstews]

I should be flogged for not zooming the pic of Cherry Annie sliders especially now I remember you mentioning those previously.

5 lashes with the "Cat of Nine Tails" ....



(Think I could go for a few of those myself)

__________________________________________

Kinda looks a little like Angelina Jolie !

Speaking of her, you should see her in this movie ..

... /// https://youtu.be/R6uQRPFfvVo \\\ ...

...... (Leaves little for the imagination) ......

[farmall]

Poor girl. There's one thing that would make her genuinely beautiful, my old gray nuts slapping her eyebrows.

Best not to imagine that in every exquisite hairy gnarled veinous wrinkly sweaty olfactory audible detail though.

[Dragstews]

Barkeep .... !! More Mead !!



_________________________________________

Oil pump has been serviced ...



Tappet blocks are also done ..
Used gaskets from the 48-52 era cause they don't have a hole in them to feed the hyd's ....
Being solids will be in use, the tappets are also from the 48-52 era ...

These motor parts will be set aside until the lower end starts going together ...
That may take a while, we decided to go with a Knuckleworks left case (65-69) ...

Just like the left case that was used on farmall's 48EL ...

This motor is seeing a few mods mostly for gaining longer engine life .
Not a lot of Hot-Rodding going on with it, but will be taking some meat off the stock left flywheel ...



Not going to be pulling a trailer or a sidehack or even packing Bertha around so a few pounds off will net a faster revving motor ...



Basically will be the same as S&S wheels ...

Can't beat it with a stick ......
.... Unless ....

... /// https://youtu.be/mxoxbFgFnqk \\\ ...

.......... (Those natives are restless) .........

(Check out the Redhead in the vid, she's got more moves than EX-lax !!)

[Dragstews]

For you truck gearheads ...

A bit of progress ...



Second coat of Por-15 ^^

Not much to see with the added three inches now ..
Looks factory ... Which was kinda what I was shooting for ..

[ExplodingCoffinEmporium]

For you truck gearheads ...

A bit of progress ...



Second coat of Por-15 ^^

Not much to see with the added three inches now ..
Looks factory ... Which was kinda what I was shooting for ..

Damn good coating, I run that or chasis saver based on what’s getting covered and have never had a disappointment over the years. If I get it on the rotisserie it’s getting coated as I’m not in the business of doing it twice due to Midwest salt bathes.

[Dragstews]

[Dragstews]

Well I'll be dipped in sh*t !!



Think it's going to turn out looking pretty dag-gum sweet ... ??



That's ^^ the first coat of epoxy primer ..
Guide coat was laid on and block sanded ...

The first photo is the second primer coat ...
Going to bolt it on the truck so it won't be dancing around while sanding it once again ...

When done with that, it should be ready for the color ...





Wetting down the fender with final wipe (Wax & Grease Remover) gives it a look like the clear been laid down ... Shows the light refraction, which can be seen by eyeballing ..
Found only one spot that need a bit more TLC ...
One more primer coat and block sanding will have it gone ..

My goal is not to have waves showing up in the final finish ...
... (Good chance I may achieve that look ??) ...



... /// https://youtu.be/l5vLsPjI928 \\\ ...

[Dragstews]

Been at it on the second rear fender for longer than I wanted to be ... "WORK" !!
Making good progress ...



Underside is done ...



Working the topside is slow go ...
____________________________________

Kinda getting a few more ducks in a row when I get around to doing the tranny swap (TH 400 to a 4L85E)

Wanted to add a bit of beef to the driveline with the installation of factory strut rods (The 75 1/2 ton 4X4 Jimmy frame that's under the Binder never had em) coming from the motor mounts going to the trans alum. dust cover ...



Came up with a used set (Santa dropped em off), powder coated them and was thinking of a way to mount em to the dust cover that came with the 4L80 trans ..
Being the trans came out of a 2000 3/4 ton Van, the dust cover didn't have the lugs, from what I understand only the 4X4's had them ..

The truck's THM 400 trans (K case), that I built so many years ago, has a dust cover with the lugs .. (Just a hanging, nothing was ever bolted up to the lugs)
Thoughts was that I could use it on the 4L80 ....



That dog won't hunt !!

Two of the mounting bolt holes don't line up with the 4L80 case and the converter is hitting the back of the cover ..
Okay, no biggie .. Some work to make up lugs and weld onto the 4L80 dust cover would get the strut rods nailed down ..



Was in the mode of hunting the material to make it so ..
Knocked on "farmall's" door to see if he had any solid alum. round stock ..

While we both (Two heads are better than one, ya know) was in the think tank on how to go about doing this mod to the Oem cover, a Buddy from my hometown in Kentucky sent to me a eBay link showing a cover that was made by GM for only 5 years that used those casted in lugs and fits the 4L80 ...
Only on the 3/4 & 1 ton 4X4 trucks ..

Problem solved ...

(Special thanks goes out to farmall, Hillbilly Josh & Santa)

[Dragstews]

(Jusssst what the Doctor ordered)




Didn't know this critter even existed !!



Fenders turned out nice ...



Hoping to start in on the front fenders here pretty soon ...
.. And "Wide Body" we will be ..





... /// https://youtu.be/KkJTmwHdOjo \\\ ...

[Dragstews]

Well Guys & Gals

Since this thread is in a eddy at the moment, thought to post up a few photos ...



She's coming together ...



One of these days I'll be pulling into a A&W ...
(Car-hop better have some stilts handy)



All that work I did on the fenders and the look is like it came from the factory that way ...



Can't wait to do the front fenders ....

[rockman96]

Damn that stance is badass!

Now, for the front fenders (wheres that 'duck' emoji?)

[Dragstews]

Here's the fenders that's going on da truck ...

What I'm doing is going from a R-100 (Bottom of the IH light truck line in 54) to a R-140 which was a factory 4X4 ...
__________________________________________



I may be a tad nuts, but I'm not bat-sh*t crazy !!

[Dragstews]

Left side flywheel got a few pounds took off and the timing marks put back on ...



This mod will make the motor run like this ....

[Dragstews]

Since this page is mostly talking about trucks, here's one "Bad-Ass" truck ....



Yes Sir .... Bad-Ass may be a understatement !!



502 crake Big Block motor with a 4L60E trans ..



Soon to have a Vintage Air unit installed ..





Owned and driven by a 94 year old Gent ...

I'm trying to hook him up with a California gal ...

... /// https://youtu.be/j7J2ZUswA2k \\\ ...

[farmall]

4L60 behind a BBC? I hope THAT gearbox got a gut rehab! Good transmission design but herptastic execution by the bean counters.

Just added one of these to the LS frame rail slicing tool kit. A two-cripple crew can skin drivetrain donors so fast it's worth the time dual saws save. (If the damn yard would get ahead of forklift maintenance instead of being reactive that would be awesome but some dreams never come true....) The short stroke remarked on in reviews is a bonus when cutting steel near obstacles. Torque and stroke rate are what matters as useful reach is determined by blade length in vehicle slaying. Saw brand isn't critical but I've got plenty of batteries from other tools so the DeWalt won the day, adding more 28V batteries to my old but superb pre-buyout Milwaukee being uneconomic.

https://www.amazon.com/dp/B086M6KKKX...roduct_details

[Dragstews]

4L60 behind a BBC? I hope THAT gearbox got a gut rehab! Good transmission design but herptastic execution by the bean counters.

Been built super Heavy-Duty ...

https://www.amazon.com/dp/B086M6KKKX...roduct_details

I should have went cordless ...