Bad-Boy 92 inch 1952 Pan

[Dragstews]

Starting a new thread where I left off on the lost thread ..

Cases made it back from "Phil Long" (I was beginning to wonder) after a lengthily stay at his shop.

Here's what Phil's hand did, a New Left Side case sporting the 69-up Timken bearing was matched to the Oem 52 right side case..



Since a belt drive will go into play had Phil relocate the case breather to the right case as in the 65-up cases ..

[Hoghead]

Looks like this is rolling again....

[Dragstews]

Owner wanted the cases shot with Gloss Black Powder-coat..
A bunch of grind time will go down in order for the powder to look nice ...

Lots of chrome will pop bolted on the black cases ...



Oil pump is the og for this motor, did the works to it ..
Oem late Lifter Blocks seen the dip tanks ..
Cam Cover is a repop of a 47 Knuck, also made a trip to the tanks ..

[Hoghead]

Lotta graft there!

[confab]

I like the Black and Chrome accents.. You can get too much shiny.

[Dragstews]

You can get too much shiny.

....... They will hear you .. !!!

[Dragstews]

What do we have here .. ??

Been so long ago I forgot .. !!

]

I see Carrillo Rods, Jim's crankpin and T&O 4-3/4" wheels ..
Special S&S Big Foot Keyed Splined Sprocket shaft ...
Pinion shaft is nothing to write home about, tis S&S but bone stock for 52 .. Does have the oil pump speed up gears ..

[mcknzAlex]

Now that's shiny. I like how the picture focuses on its subject and blurred the background. LOL

[Dragstews]

Hope to get around to lapping the pinion case bushing to size today ...
Might have the need to replace the case bushing with a new one cause the one in the case now is the og that the motor had .. Could be worn past max oversize bearings ... ??





Will install the Timken, set up the lap and do a few spins, then load new bearings for a test fit ...
After the bearing running fit has been accomplished, can dial in the breather timing and fit the case window to the gear window ..



That's a bit of a job to do on the 57 and back motors, but this motor will have a S&S breather gear (With a Don Hotop air ramp) which has more open timing built in. Makes for less work on the case breather window ...



The install of the "Air Ramp" requires getting rid of the blow-up arresting screen ...



Odds are in favor of dat not happening .. !!
_________________________________________

These tools makes for easy install of the bearing ...

[Dragstews]

Matched the case window to the S&S gear window ... Didn't take any meat off the open and closing sides of the case window .. Yet ..
Gotta hook up a degree wheel in order to see the timing ...





Just about ready to do the lapping ...

Brand new repop Pan jugs ...





Bored those puppies .060" oversize to get to 3.5" bore ..
The S&S Stroker Pistons allow for stock height jugs ... In turn the 92 inches are hidden, motor is a "Sleeper" !!

[StuJ66]

Compliments to you. Have read quite a few of your build threads. Very detailed they are. If I ever get my grubby hands on a pan, it would be a no brainer sending it your direction.

[Dragstews]

... /// https://youtu.be/MfvVIoWTCzI \\\ ...

... !! Yo King !! ...

... /// https://youtu.be/4uw96R8CMyU \\\ ...

[Dragstews]

Good Golly, Miss Molly ....

Owner is wanting to send me a 53 Pan to do my magic on ...



Shoot ... Not even at the half way mark with the 52 at the moment ...
He wants the same gig done on the 53 ...



Not necessary in that order ...


____________________________________



Yeah Baby, yea ...

That NOS Hi-Po oil pump will not be going on the 52 ..
I wonder if anybody remembers this pump that hasn't been made in 30 years .. ??

Hint; Same pump that's on my 52 Pan/Shovel ..



The cast iron pump being plated will have just as good of looks as the mystery Hi-Po pump ... Nowhere close to having the same flow numbers ..



Moon eyes gauge is a must have ..

[Dragstews]

Located the top-end oil drains in the case deck ...
Can finish drilling the drains once the case is back apart .. Will be using the jug drain holes as a drill guide ..





The jugs have the drain back holes lowered ..
Pressed in a slug to block off the original holes and drilled new holes ...


__________________________________________________ ____

Since the owner is wanting a slick powdercoat job some grind time will be spent on cleaning up and matching the cases ..





`Same goes for the lifter blocks ..



How bout that ^^ Five years into the run of the Panheads and still have leftover casting from the Knucks ...





.... "Not Anymore" ....

That should net a better look from the powdercoat ...



The repop left case had a huge lip sticking out, pretty much got it gone..

Not going to flow in the rest of the case cause the gen will hide most all of it .. Only what the eye can see ...

Shoot .... Need some music to go along with eyeballing the thread ...

How bout "Hey Joe" Acoustic Style ...

[Dragstews]

Did some work on the case breather in order to net a better look than what was ...