CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Sugarcubes

Page 1 of 8 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. I believe Andrews previously made the kit and...

    I believe Andrews previously made the kit and V-twin may have copied it. Andrews show it as discontinued on their site but you could try Dennis Kirk or JP cycles to see if they have any of them or...
  2. get it all back together when your parts arrive...

    get it all back together when your parts arrive and take the bike out for a good run on open road so you can get a feel for the power delivery through the rev range. pull over after 20 miles or so of...
  3. Replies
    4
    Views
    202

    Guess it depends on what is local to you. There...

    Guess it depends on what is local to you. There are some country-wide registered official clubs here that as a member would entitle you to discounts on insurance premiums, e-zines, the odd discount...
  4. Thread: evo chop.

    by Sugarcubes
    Replies
    57
    Views
    9,883

    awesome work. I love those fender struts. Bike is...

    awesome work. I love those fender struts. Bike is clean and simple!
  5. plugs look ok but if it was me, I would probably...

    plugs look ok but if it was me, I would probably back the idle mix screw out a quarter turn to lean it out slightly. Its probably too much choke when starting / sitting in traffic thats darkening em...
  6. I run the factory CV carb on my 1995 evo big...

    I run the factory CV carb on my 1995 evo big twin. To be honest, Ive only ever used CVs whether its on a 70s chop or a more modern evo.
    I find them very easy to work on and you can dial them in...
  7. Replies
    17
    Views
    553

    nowadays, clean unmolested bikes like that are...

    nowadays, clean unmolested bikes like that are getting harder and harder to find. Its your bike so you can do whatever you please but if it was me I would keep it, ride it and enjoy it as is. If you...
  8. Replies
    21
    Views
    1,263

    start from the top and work down - is the...

    start from the top and work down -

    is the frame neck straight
    are the trees bent
    are the forks / fork lowers bent
    is the axle bent
    is the rim trued
    is the wheel hub out of whack
  9. Can it be done? Most definitely. Led Sled built a...

    Can it be done? Most definitely. Led Sled built a real nice chop out of a nightster some years back.

    The stock modern sportster frames have thicker diameter tubing than the 70's ironheads and...
  10. Replies
    7
    Views
    797

    You can retro fit the early, clean looking dash...

    You can retro fit the early, clean looking dash from the panheads / shovelheads or the cats-eye dash from the knuckle. You just need to do a little modifying of the base plate. I put a rear wheel...
  11. Thread: 41 el

    by Sugarcubes
    Replies
    635
    Views
    17,182

    None of us are born experts. Learning as we go is...

    None of us are born experts. Learning as we go is all part of the fun of old machines! To be fair my problem is always over torquing till the bolt snaps ha! Be good to see it out on the roads
  12. Replies
    12
    Views
    656

    old throwback issues of The Horse were always my...

    old throwback issues of The Horse were always my fave. 80s/90s issues had some wild bikes with some heavy duty motors too
  13. Thread: 41 el

    by Sugarcubes
    Replies
    635
    Views
    17,182

    good news. Any vids of her running just yet?...

    good news. Any vids of her running just yet? hopefully get it to the hook up this year eh
  14. Thread: Sportster

    by Sugarcubes
    Replies
    10
    Views
    385

    are you looking to do one of those nyc chopper...

    are you looking to do one of those nyc chopper style filter relocations to the rear of the frame??
  15. Replies
    40
    Views
    1,300

    slimer always was a bit problematic but he comes...

    slimer always was a bit problematic but he comes good in the end :D
  16. Replies
    23
    Views
    790

    I like the way you took the arms off and then...

    I like the way you took the arms off and then trimmed down the flat bar that sits just behind the oil tank. I didn't take half as much time on mine and hacked off the arms with a handsaw, figuring...
  17. That sounds more like it! Run that stock filter...

    That sounds more like it! Run that stock filter and bump up your main jet, you should be good to go
  18. That sounds pretty damn low for a 1340? most...

    That sounds pretty damn low for a 1340? most stock healthy 80" evos seem to run around 145PSI per cylinder.
    Was that with the throttle wide open?
  19. Replies
    16
    Views
    652

    for the money you would end up shelling out on a...

    for the money you would end up shelling out on a set of flanders or stellings, youd be far cheaper just asking an established fab shop to make you some "0"bars as per the spec on Tattoos catalogue. I...
  20. Replies
    40
    Views
    1,300

    i kinda like it! id call it Slimer!

    i kinda like it! id call it Slimer!
  21. My 1995 evo 1340 had the Dynojet kit in it and i...

    My 1995 evo 1340 had the Dynojet kit in it and i replaced it with stock HD kit. I also installed the EV27 cam and I can bet you right now you are running too small a main jet.
    The andrews website...
  22. Replies
    12
    Views
    706

    i never like the position of low bars combined...

    i never like the position of low bars combined with forward controls. With mids, low bars are comfier but for me a nice set of low-ish 8" rise ape style bars are the comfiest
  23. Replies
    7
    Views
    364

    Solid advice there. I have a stock length...

    Solid advice there. I have a stock length springer that sits my rails level and i still scrape on even the most mild of bends. Its a bit of a pain
  24. Replies
    2
    Views
    266

    That's the info im looking for! Thanks Jim

    That's the info im looking for! Thanks Jim
  25. Replies
    2
    Views
    266

    Evo stroker kits

    Does anyone have any experience with how the mid-late 1340 Evo cases tolerate the S&S 96" stroker kits?
    I really shouldn't have read Dragstew's build thread about that Ironhead monster he is...
Results 1 to 25 of 199
Page 1 of 8 1 2 3 4

Log in

Log in