CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: kdub13

Search Forums: Search took 0.01 seconds.

  1. yup... got one of those. Unfortunetly my late...

    yup... got one of those. Unfortunetly my late shovel manual is no match for my early ratchet top. Which is why I came here for help. But I guess im back to square one.
  2. Yeah when it is placed in front, this is where...

    Yeah when it is placed in front, this is where the stopper lands on the starter gear.

    Here is a photo with the spring and arm on. The arm lands at about 11 o clock.

    I am getting my info from...
  3. I had the spring off so you can see where the...

    I had the spring off so you can see where the slot is for the spring.

    The bushing is lubed and good to go. When I took it off, and re trace my steps on the kicker cover I found that the stop was...
  4. Ratchet top kicker Arm falls when the bike is running

    Hey all, I just canít seem to figure this out... I have a late 60s ratchet top trans here, and when installed, and the kicker cover gets put on, everything works fine, clutch works good, kick starts...
  5. Replies
    4
    Views
    581

    That is very cool, I have never seen an oil...

    That is very cool, I have never seen an oil filter there before, I just ran some very short line from the oiler, to the return. Easiest solution for now til I can figure out that badass oil filter...
  6. Replies
    4
    Views
    581

    Plugging off primary oiler?

    Hey there,

    I am doing a bunch of research about plugging off the primary oiler and oil return on my shovel, but I can not find anything about what to use to do it? Do I need to tap the oil pump?...
  7. Can Anyone confirm Vermont Reg still works in 2018?

    Hey folks! Well my baby is finally done and ready to rip, only thing is I need to get a plate on the damn thing. I have read a lot about the ol' Vermont loop, but everything is dated back to...
  8. Replies
    25
    Views
    3,668

    Yeah if I went all OCC on my down post I would...

    Yeah if I went all OCC on my down post I would have gained about a quarter inch to get the belt on over the front pulley. But the belt would have still been too tight to run at that length. So the...
  9. Replies
    25
    Views
    3,668

    @47str8leg it is still an 8mm belt as far as the...

    @47str8leg it is still an 8mm belt as far as the spacing of the teeth go... it has more teeth, instead of 138 it has 142 teeth. It should give me about a half inch to an inch more room.
  10. Replies
    25
    Views
    3,668

    Went with a little longer belt to keep the same...

    Went with a little longer belt to keep the same ratio on the pulleys... Thanks.
    If anyone needs a 138 x 1.5" BDL belt hit me up, its brand new. Thanks
  11. Replies
    25
    Views
    3,668

    It is hitting the frame... After speaking with...

    It is hitting the frame... After speaking with BLD he said there is supposed to be a flat spot in the down post where the trans can get a little more wiggle room. But my frame does not have it. So...
  12. Replies
    25
    Views
    3,668

    Shovelhead open belt primary belt wonít fit

    Hey guys, Iíve been researching and researching but canít seem to find a solution to the problem Iím having.

    The belt on this BDL 1.5 open primary seems just a tad short. I canít get the damn...
  13. Replies
    6
    Views
    1,427

    @dragstews sweet thanks for that. Cheers

    @dragstews sweet thanks for that. Cheers
  14. Replies
    6
    Views
    1,427

    Thanks guys... If I ran with out it, wouldn't...

    Thanks guys... If I ran with out it, wouldn't there be an alignment issue to the motor? that bearing support sticks out doesn't it... Would spacers be required? Or maybe that overbearing will give me...
  15. Replies
    6
    Views
    1,427

    Shovelhead Trans/Open Primary question

    Hey guys... quick question... I have a cone shovel I am building and am going to run a BDL 1.5 open primary on it, kick only... which I already have... I also already have a 1965 Harley ratchet top...
Results 1 to 15 of 15

Log in

Log in