CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: farmall

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.07 seconds.

  1. Replies
    3
    Views
    92

    Best to save the e-start takeoff parts too since...

    Best to save the e-start takeoff parts too since age and bad knees happen.

    I also replace charging systems rather than ride old parts until failure. HD stator cooling is poor because of the rotor...
  2. Replies
    6
    Views
    242

    I don't notice any difference betwen floating and...

    I don't notice any difference betwen floating and non-floating rotors on the street but there's no reason not to run them.

    I was delighted to be rid of the single pot calipers as was my bro when...
  3. Replies
    17
    Views
    343

    The ten-tooth smaller "wrong" basket will have a...

    The ten-tooth smaller "wrong" basket will have a much smaller OD givem the same tooth pitch belt. Thickness should be similar but I've not fondled either part.

    That of course will not have...
  4. Replies
    17
    Views
    343

    Old belt drives and parts turn up (and you can...

    Old belt drives and parts turn up (and you can always ask dismantlers) on Ebay and cheaper on Facebook groups (I only deal with sellers who use PayPal or take cash face-to-face).

    What does the...
  5. Replies
    6
    Views
    242

    They're fine daily rides. The fork swap is...

    They're fine daily rides.

    The fork swap is easy. You just weld a 1" wide hunk of flat bar to the front of the downtube as a fork stop (properly, no shitbox 120v FCAW machines). No need to remove...
  6. Replies
    17
    Views
    343

    Do post closeup kit parts pics, especially of the...

    Do post closeup kit parts pics, especially of the timing side of the kit since the Tech Cycle website design does them no favors (much larger high res pics would sell more product).

    Instruction...
  7. Replies
    4
    Views
    226

    I never measured them nor cared since I've never...

    I never measured them nor cared since I've never replaced fiber clutch plates with stock parts having none lying about but it would make sense for them to have thicker friction material to reduce...
  8. Replies
    17
    Views
    343

    I likely referred someone to Dragstews who did...

    I likely referred someone to Dragstews who did the engine work on my Pan plus other stuff. I'm a happy customer!

    My Pan project has a five speed that already takes the Denso starter and will run...
  9. Replies
    4
    Views
    226

    Cop use means more clutch slipping in low-speed...

    Cop use means more clutch slipping in low-speed riding due to the start-stop nature of traffic patrols.
  10. Replies
    19
    Views
    722

    If it was titled in his name and she has...

    If it was titled in his name and she has paperwork naming her executor she can transfer the bike to you. Best smoothest way would be you get with her and take her to the DMV with that paperwork so...
  11. That check ball mod would also work for butterfly...

    That check ball mod would also work for butterfly Keihins now that Andrews quit making that original (early) style pump cover.

    Interesting the clones lack them.
  12. Replies
    6
    Views
    201

    Pinching them by visegrip is one way I break...

    Pinching them by visegrip is one way I break torque then soak in penetrant after heating and leave overnight if very stuck, or just rock them back and forth a few degrees ten or fifteen times to help...
  13. Replies
    4,298
    Views
    422,333

    https://www.youtube.com/watch?v=_HNyl-Thqik ...

    https://www.youtube.com/watch?v=_HNyl-Thqik

    Select auto-translate to your preferred language.
  14. Replies
    746
    Views
    45,890

    Poor girl. There's one thing that would make her...

    Poor girl. There's one thing that would make her genuinely beautiful, my old gray nuts slapping her eyebrows.

    Best not to imagine that in every exquisite hairy gnarled veinous wrinkly sweaty...
  15. Replies
    746
    Views
    45,890

    A veritable cornucopia of vintage bits! I...

    A veritable cornucopia of vintage bits!

    I should be flogged for not zooming the pic of Cherry Annie sliders especially now I remember you mentioning those previously. If I find a set I've a...
  16. Replies
    746
    Views
    45,890

    Nice strategic use of black there. Wheel time...

    Nice strategic use of black there.

    Wheel time approaches. What's the detailed recipe for that front end? Looks like bored (39mm?) trees w. Wide Glide tubes/sliders.

    I was considering a Norton...
  17. Replies
    746
    Views
    45,890

    If ya know anyone who Cerakotes (mostly...

    If ya know anyone who Cerakotes (mostly gunsmiths) future customers may prefer that because it's far tougher than paint or powder and doesn't chip. Not even rifle bore cleaner fucks with Cerakote and...
  18. Replies
    19
    Views
    722

    I expect to rebuild these old machines axle to...

    I expect to rebuild these old machines axle to axle. Just firing it up then riding it is popular (new owner excitement) but does nothing good for the machinery. Evaluation by inspection and testing...
  19. Thread: Wheel question

    by farmall
    Replies
    13
    Views
    324

    Easy way to find out what Lowbrow or any other...

    Easy way to find out what Lowbrow or any other parts fit is call or email their tech support. Advert captions lack detail.
  20. Replies
    4
    Views
    224

    You can take the .pdf to any decent office store...

    You can take the .pdf to any decent office store and have it printed, punched and bound on quality stock. They figured out they can save serious money not offering dead tree manuals so those went...
  21. Replies
    1
    Views
    161

    There is nothing wrong with anaerobic thread...

    There is nothing wrong with anaerobic thread locker used per instructions. It's used on billions of fasteners in production. I used it on all sorts of hardware without problems and nearly always use...
  22. Replies
    746
    Views
    45,890

    That brings back memories of SBC exhaust manifold...

    That brings back memories of SBC exhaust manifold warpage! Still have some rams horns on the wall.

    You could also run bolts through the engine mounts (head side out) with enough extended after...
  23. Replies
    746
    Views
    45,890

    Yup. Accidents will happen. (resumes drooling on...

    Yup. Accidents will happen. (resumes drooling on shoes...)
  24. Replies
    746
    Views
    45,890

    While I never had problems with the ThreeBond...

    While I never had problems with the ThreeBond family that post reminds me an old idea I had (and may have posted but I'm too lazy to look) for a powerful cheap effective no-pry case splitter.
    ...
  25. Replies
    7
    Views
    621

    One of my bros was helping another replace Twin...

    One of my bros was helping another replace Twin Cam timing chain guide shoes.
    All seemed well until a few days later when the bike wouldn't start. They were chasing various possible problems but...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in