CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: misfitJason

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.09 seconds.

  1. Replies
    15
    Views
    182

    nope....not me. I am a Floridian

    nope....not me. I am a Floridian
  2. Replies
    15
    Views
    182

    I am running alto plates and steels with a V111...

    I am running alto plates and steels with a V111 and 3 inch bdl and it holds.

    Bdl is easy to mess with for higher hp applications. You could add more springs or get their lockup addition so it...
  3. Replies
    45
    Views
    1,994

    I look forward to the new ones. Seems like a...

    I look forward to the new ones. Seems like a positive step forward.
  4. Yes polish it and run the spring with the cover!

    Yes polish it and run the spring with the cover!
  5. Did you remove the plug from the carb when you...

    Did you remove the plug from the carb when you installed the new backing plate for the air cleaner? If I’m not mistaken the mooneyes ones block the vent that the stock one has a hole for

    I was...
  6. Replies
    2
    Views
    235

    click on their name and it will bring up their...

    click on their name and it will bring up their profile. You can click the send a private message button
  7. Replies
    3
    Views
    398

    that's unique

    that's unique
  8. WHat all do you need yet or are you looking for?...

    WHat all do you need yet or are you looking for? I can go through my parts horde for ya to see if there is anything I can send you for your efforts
  9. Thread: 99 dyna

    by misfitJason
    Replies
    6
    Views
    344

    I think I remember his previous threads. If I...

    I think I remember his previous threads. If I remember correctly the problem was his cylinder would become out of round and the piston fit was not proper
  10. Thread: 99 dyna

    by misfitJason
    Replies
    6
    Views
    344

    Stop buying store bought kits! Get a pair of...

    Stop buying store bought kits!

    Get a pair of seasoned cylinder bored to 95 inches (you can up to 98 but it make the liners thin) properly to fit a pair of new pistons with proper ring gap....
  11. Replies
    3
    Views
    455

    More specifically a set of gma brand controls...

    More specifically a set of gma brand controls should work for what you’re after. Most of the stock take offs don’t have the master attached to them for an evo.

    On a side note fab Kevin sell...
  12. Replies
    5
    Views
    479

    I will give you some experience I know from guys...

    I will give you some experience I know from guys that used or use them. They say the ignition isn’t bad but the coil that comes with it is a hunk of crap.

    I personally have a ultima six speed...
  13. Replies
    15
    Views
    1,036

    I like it better with your add on

    I like it better with your add on
  14. Replies
    13
    Views
    1,169

    Looks very sharp!

    Looks very sharp!
  15. That’s some fancy brass!

    That’s some fancy brass!
  16. Replies
    23
    Views
    1,176

    My first place to check would be Paughco

    My first place to check would be Paughco
  17. Replies
    10
    Views
    659

    Well, I have always thought my acrs didn’t...

    Well, I have always thought my acrs didn’t function properly since I bought the motor new. I ordered up some new ones to replace the old ones. When I got the new ones they were super easy to depress...
  18. Replies
    10
    Views
    659

    This is an excellent Idea and I still have my...

    This is an excellent Idea and I still have my stock starter motor to install back in to try.
  19. Replies
    10
    Views
    659

    The relay is new and I just wired it up when I...

    The relay is new and I just wired it up when I put the motor in. Like I said before it does it regardless of me using the automotive button wired up to the realy or just the starter solenoid button...
  20. Replies
    10
    Views
    659

    I will try it with the plugs out. The starter...

    I will try it with the plugs out. The starter relay is wired in parallel with the starter relay. Even if I manually push and activate the releases it still stalls out.
  21. Replies
    10
    Views
    659

    I was thinking of the binding issue. The starter...

    I was thinking of the binding issue. The starter I put in a month before I got the new motor and all grounds are tight and good.
  22. Replies
    10
    Views
    659

    Weird starting issue question

    Bike info:
    Custom built softail
    V111 motor
    Ultimate six speed trans
    All balls 1.4kw starter
    Automotive start button and starter solenoid button
    Bdl open 3 inch primary


    I have been having...
  23. Rad bike!

    Rad bike!
  24. Replies
    6
    Views
    1,454

    looks killer man!

    looks killer man!
  25. Best bang for the buck would be getting your...

    Best bang for the buck would be getting your cylinders bored to 1200. Buy a used set of 1200 takeoff heads and get them serdi’d. The 883 heads cost too much to get the work done to get them...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in