CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Nimrod

Page 1 of 5 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    63
    Views
    3,451

    I had the same setup when I first got my CB a few...

    I had the same setup when I first got my CB a few years ago. I had the same problem as in your first post, seemed to be low power in higher gears. Short story, ended up with a 260 main and timing...
  2. Replies
    3
    Views
    1,260

    I think they are all the same. Call Red and he...

    I think they are all the same. Call Red and he can tell you for sure.

    918-479-4200

    http://www.cycleonemanufacturing.com/
  3. Replies
    2
    Views
    479

    there were 2 sets of carbs for those motors,...

    there were 2 sets of carbs for those motors, known as roundtops and keyholes.

    the roundtops came on the 69-76 motors, and the keyholes came on the later super sports in 77 and 78.

    the...
  4. Replies
    1
    Views
    932

    Call Red at Cycle One. He will know, and if you...

    Call Red at Cycle One. He will know, and if you need parts he will have them. If the stem isnt right, he can make one.

    918-479-4200
  5. First thing you should do is get a manual. these...

    First thing you should do is get a manual. these are easy to work on, follow it and you will be ok. Next, get an impact screwdriver, you will need it to break those crappy soft headed screws loose....
  6. Replies
    0
    Views
    282

    Front end spring questions

    I have a 39mm front end and want to raise the ride height. Seems that the PO lowered it by cutting off the springs and putting in 3" spacers on top of the spring.

    The springs in the tubes are 18...
  7. Replies
    96
    Views
    19,259

    this is badass. I think I heard a little...

    this is badass. I think I heard a little separation in the firing, maybe the wind though. these things should sound like a hum. Dont be afraid to set the ignition timing by ear, shit gets worn and...
  8. Replies
    17
    Views
    2,385

    Im with CarloFreeze and AlleyOop. As much as I...

    Im with CarloFreeze and AlleyOop. As much as I love teh CB750, 2500 is overpriced. Only the uninformed and impatient to get a chopper would pay that, go over with cash, I think $1,500 is fair, and...
  9. Replies
    22
    Views
    2,179

    Here in OKC its a Lunchbox at Ednas. Orange...

    Here in OKC its a Lunchbox at Ednas. Orange juice, amaretto, and Coors Light. sounds gross, but its delicious.
  10. Replies
    9
    Views
    1,172

    Call Kate and tell her what you need. She will...

    Call Kate and tell her what you need. She will hook you up.

    http://www.cycleonemanufacturing.com/id298.html
  11. Replies
    7
    Views
    471

    Ive tuned these bikes with the same set up, not a...

    Ive tuned these bikes with the same set up, not a big deal. In my experience, most shops aren't good with these old bikes and you will do better on your own. Not a big deal.

    You're problem more...
  12. Replies
    7
    Views
    471

    I have a Dyna ignition and coils, and the coils...

    I have a Dyna ignition and coils, and the coils are mounted under the seat. Plug wires are ran between the carbs and through the holes in the jugs, then up to the plugs. And, my plug wires are...
  13. Replies
    4
    Views
    564

    Hit the guys at Chopper Supply co. up. Good...

    Hit the guys at Chopper Supply co. up. Good dudes, they will send you in the right direction.
  14. Replies
    6
    Views
    1,479

    l laughed way too much at this. booty infiltrate.

    l laughed way too much at this. booty infiltrate.
  15. Replies
    36
    Views
    2,244

    You can make the fucking sandwiches. Then use...

    You can make the fucking sandwiches.

    Then use her as a serving tray to deliver said sandwiches to your bros. Just grab her hair, cram your booger hook in her pooter and lift.
  16. Replies
    36
    Views
    2,244

    Very fucking sick. But I wont judge you for it,...

    Very fucking sick. But I wont judge you for it, but what about if she had one arm, or at least 1/2 an arm to put up some sort of fight? you know, like knocking you in the jaw with an elbow nub.
    ...
  17. yes please

    yes please
  18. Poll: 65228

    65228
  19. Replies
    2
    Views
    487

    After I had my heads redone, I was looking them...

    After I had my heads redone, I was looking them over and saw a little line on one of the keepers, and went to feel it with a pick to see if it was a crack and it was, the keeper shot out. The other...
  20. Ill try the heat before the air impact. Im going...

    Ill try the heat before the air impact. Im going to bet they have loctite on them.
  21. Still on the bike. Im wanting to change out the...

    Still on the bike. Im wanting to change out the hex drive chrome plugs with brass ones. Has acorn nuts on the other end. Just cant get the plug to break loose without the rocker shaft spinning. I...
  22. Shovelhead rocker shaft plug-how do you break them loose?

    I tried using a hand impact driver, putting 2 jam nuts the other end, and nothing seems to get them to break loose before the rocker shaft starts spinning. Any tips on how to break them loose while...
  23. Replies
    11
    Views
    1,020

    Third Eagle of the Apocalypse is a title not to...

    Third Eagle of the Apocalypse is a title not to be fucked with. Ive watched a few more his videos, and this guy is trying to warn you motherfuckers. Apparently, Gary Busey getting eliminated from...
  24. Replies
    68
    Views
    3,147

    This is where its at. My midgets would alternate...

    This is where its at. My midgets would alternate between stormtrooper and robocop costumes. I would buy a big ass helicopter, with a bar in it, and me and my midget army would fly around to protest...
  25. Thread: Guns

    by Nimrod
    Replies
    1,378
    Views
    182,254

    There are videos on youtube on how to clean up...

    There are videos on youtube on how to clean up some contact surfaces and make the trigger smoother, but not lessen the pull weight. if you follow the videos, it does help alot, but it is just as...
Results 1 to 25 of 114
Page 1 of 5 1 2 3 4

Log in

Log in