CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: DustyDave

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    3
    Views
    245

    old thread answered way back! But if you click on...

    old thread answered way back! But if you click on the thumb nail It should switch to a 640x480 large image
  2. Replies
    11
    Views
    214

    That thread had had multiple replies and had...

    That thread had had multiple replies and had faded into the past. I suspect we been hacked!
    Dusty
  3. Replies
    3
    Views
    245

    Anybody know anything about this?

    This is stamped before and after the serial number on an aftermarket Knucklehead case.
    103901
    Anybody recognize it?
    Dusty
  4. Replies
    69
    Views
    2,214

    Poll: All this talk bout fishing reminded me that I...

    All this talk bout fishing reminded me that I hadn't scared the brown trout out of their favorite cut banks in a while. So I took El Indio up a forest road at about 7500 ft that had all the camping...
  5. Replies
    17
    Views
    381

    As good as I could get without putting it up on...

    As good as I could get without putting it up on the lift. Had a honda master on it for a few years when it went bad I picked this Chinesey copy off Fleabay and it seems fine....
  6. Replies
    17
    Views
    381

    It's kinda hard to see but here is one like the...

    It's kinda hard to see but here is one like the top one mounted inside the frame rail with the reservoir bolted to the back of the primary on my 50 Scout. It is operated by a cross shaft....
  7. Replies
    19
    Views
    370

    Try DOT 3 brake fluid Takes most paint off and...

    Try DOT 3 brake fluid Takes most paint off and leaves the aluminum surface alone. Not as fast as aircraft stripper but cleans up with brake clean and leaves the aluminum looking way better.
    Dusty
  8. File right away you can always drop the dispute....

    File right away you can always drop the dispute.
    Dusty
  9. Replies
    39
    Views
    1,408

    dot 3 brake fluid takes wrinkle paint off without...

    dot 3 brake fluid takes wrinkle paint off without affecting the aluminum finish and cleans up with brake cleaner. Course they may have sanded it before paint. I've never tried it on JB Weld but it...
  10. Replies
    3
    Views
    185

    4130 chrome molly tubing makes the best bars....

    4130 chrome molly tubing makes the best bars.
    Dusty
  11. The market for Harley parts might be down a tad

    Went to Capital Scrap for our usual Friday rumage. Found a few harley parts.
    https://i.postimg.cc/dVb77B42/20200515-150304.jpg
    We rummaged around for about an hour lots of stuff, a stack of twinkie...
  12. Replies
    12
    Views
    511

    I made a pair for an old Iron worker that had...

    I made a pair for an old Iron worker that had taken way too many falls. He sat on the bike with a grip in each hand in the position that they hurt the least, I measured carefully and photographed...
  13. Replies
    15
    Views
    457

    When the generator mounting bolts both broke...

    When the generator mounting bolts both broke north of Salt Lake I was real proud of that mag. Put the genny in a saddle bag and wired a reflector I stole fo the highway over the hole and off I went....
  14. First thing I do Is pull the timing plug and...

    First thing I do Is pull the timing plug and figure out where the crank set all those years and if I got lucky and it wet sumped. If the rods were at the top the chances of there not being any rust...
  15. Replies
    16
    Views
    524

    I bought these in January 2011 from Lowbrow. They...

    I bought these in January 2011 from Lowbrow. They are just right for me. Shame they aren't around anymore.
    https://i.postimg.cc/gk5d2pPX/IMGP0979-zpsc1d8aa35.jpg...
  16. A zener diode holding a power transistor...

    A zener diode holding a power transistor conducting until the voltage drops below the zenner value is old school. Now it's much easier and adjustable. ...
  17. Replies
    10
    Views
    353

    I think that single point thread IN GRAD8 will...

    I think that single point thread IN GRAD8 will still be stronger than the threads in an 80 year old castings no matter how tight I fit them.
    DUSTY
  18. Replies
    10
    Views
    353

    I asked a friend and he said you dumbass just buy...

    I asked a friend and he said you dumbass just buy long grade 8 bolt and use the threads that are already there for the top. Saw it to length and cut your custom threads on the sawed off end. Never...
  19. Replies
    5
    Views
    272

    If memory serves the duel leading shoe Honda...

    If memory serves the duel leading shoe Honda brakes had a stay rod and the duel leading shoe Yamaha had the casting that locked on to the fork.
    Dusty
  20. Replies
    10
    Views
    353

    The Bonneyville Scout uses cylinders that are at...

    The Bonneyville Scout uses cylinders that are at least 78 years old and and I have some as old as 85 in my stash. I don't want to insert every hole. So I plan to single point oversize studs since...
  21. Replies
    5
    Views
    347

    A garage sale leather purse makes a pretty gooder...

    A garage sale leather purse makes a pretty gooder most durable sandbag for metal forming. Hammer forming will get you by , but is berry labor intensive. I owned one of the very first Moto Guzzi 1973...
  22. Replies
    39
    Views
    1,408

    Wonder if they ever sobered him up? Dusty

    Wonder if they ever sobered him up?
    Dusty
  23. Replies
    10
    Views
    353

    Question bout what steel to use

    I need to machine some studs with custom threads and would like to end up with similar to grade 8 strength, free machining is desirable. Which steel do I want to use?
    dUSTY
  24. Replies
    28
    Views
    863

    About 80% of GS stators that read open just need...

    About 80% of GS stators that read open just need the crappy wires that run through the side cover replaced.
    Dusty
  25. Replies
    154
    Views
    21,713

    Proly won't talk much bout piston, head shape or...

    Proly won't talk much bout piston, head shape or cam timing. But right now I have no plans to drill into the top ring land.

    I'm not expecting to make usable power above 4000 Talked to James...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in