CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: razorrichter

Page 1 of 2 1 2

Search Forums: Search took 0.05 seconds.

  1. Replies
    22
    Views
    3,544

    The rear shocks are just some cheap 10” eBay...

    The rear shocks are just some cheap 10” eBay shadow shocks
    The spokes came from Buchanan spokes kbsa201sz Is the kit for HD rim
    I’ll measure the bars when I get out to the shop
  2. Replies
    22
    Views
    3,544

    Progress

    Iíve done a poor job of keeping up on this project updates but Iíve ground and DynamicLy balanced the crank. Full valve job. And all new bearings. I laced up a 16 inch rear rim and got almost...
  3. Replies
    22
    Views
    3,544

    The old dude that hooked me up with the A10 is a...

    The old dude that hooked me up with the A10 is a huge matchless guy he helps run the owners club so getting a matchless from him isn’t easy ��
  4. Replies
    22
    Views
    3,544

    Top end popped off

    Sound an unsatisfactory surprise inside. Cylinder blown out repaired and sleeved not cool. Some cut up pistons and a few other repaired I can see but nothing that canít be fixed!
  5. Replies
    22
    Views
    3,544

    Inspiration

    Just a few bikes I found kinda get me motivated and in the right direction
  6. Replies
    22
    Views
    3,544

    Excitement

    Iím debating on the fit and finish of this build I have considered leavening the exterior filthy but I am tempted to also make it pristine? I canít stand that chrome I think I need to strip it all...
  7. Replies
    22
    Views
    3,544

    Engine

    Iíll have to check out that guys site and gather some ideas as far as for sure plans, SRM oil pump and a Iíll grind and dynamic balance the crank and obviously bearing replacement all around and full...
  8. Replies
    22
    Views
    3,544

    A10 survivor

    First year swinging arm a10 survivor Iím going to try and keep as original to this as possible pretty excited about this one
  9. Replies
    42
    Views
    7,658

    Thanks man it’s been fun! Still have a ways to...

    Thanks man it’s been fun! Still have a ways to go!!
  10. Replies
    42
    Views
    7,658

    https://youtu.be/-yYnoTbiKQk

    https://youtu.be/-yYnoTbiKQk
  11. Replies
    42
    Views
    7,658

    Running but far from done

    Took it to torque fest but needs a lot before Iíd call it doneish
  12. Replies
    42
    Views
    7,658

    Progress..... torque fest is soon

    Iím bringing this trap to torque fest in Dubuque IA may 4 so here is more progress shots. Need to slap on trispark this weekend
    Welding will be done tomorrow
  13. Replies
    1
    Views
    398

    Vintage torque fest

    Just wanted to put this out there itís a huge amazing show but bike section needs to grow so thought it put it on here http://vintagetorquefest.com/
    Located in Iowa
  14. Replies
    42
    Views
    7,658

    Cockeyed intake

    Carb top touched the frame so made a two into one with a tilt ready to go
  15. Replies
    42
    Views
    7,658

    Tank

    Got the tank paint done up by my kid brother
  16. Replies
    42
    Views
    7,658

    I would love to except the frame ends under the...

    I would love to except the frame ends under the trans and that puts my feet too far back.... hip cramps dude
  17. Replies
    42
    Views
    7,658

    I’m glad you say that I was thinking about that...

    I’m glad you say that I was thinking about that and now seeing yours I feel like I could get away with it for sure that will be the plan then as far as the tensioner I think I’m going to try and...
  18. Replies
    42
    Views
    7,658

    Well....

    I was hoping no one would notice the riser haha it was inspiration for a chain tensioner I have now ditch that idea Iím probably just gonna buy one.... again the point of this build was to spends no...
  19. Replies
    42
    Views
    7,658

    More progress

    Single carb manifold lines the carb up to hit the frame so I moded one with a single cylinder manifold just need to weld it made progress on clutch and got the forks chopped and dropped
    Next is...
  20. Replies
    42
    Views
    7,658

    Front end started

    Pulled the springs to get a right height so I can mod them for this stance
  21. Replies
    42
    Views
    7,658

    Trans support

    This is fiction donít do that donít weld bearings. That being said I wanted to make a quick support for the exceptionally lone main shaft that holds the rather heavy scissor clutch so I hope this...
  22. Replies
    42
    Views
    7,658

    Clutch mock up

    Still need to make some kind of main shaft support
  23. Replies
    42
    Views
    7,658

    Oh yeah I still have a lot of shit I want to add...

    Oh yeah I still have a lot of shit I want to add to the frame to make it more of a frame
  24. Replies
    42
    Views
    7,658

    More mockery

    Got the frame welded together I always forget how spaghetti based Royal enfold frames are. Engine is in place still need to get primary sorted Iím planning on running it open seems like a greatly...
  25. Replies
    42
    Views
    7,658

    Getting there

    Mock-up then mock-up
Results 1 to 25 of 43
Page 1 of 2 1 2

Log in

Log in