CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ExplodingCoffinEmporium

Page 1 of 7 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. I run the same setup as Doom in terms of my...

    I run the same setup as Doom in terms of my transmission plate/adjuster on my BDL 1.5” and it’s been solid. I have not personally used the adjuster your referencing but I did have a few buddies who...
  2. Replies
    20
    Views
    330

    You should do it right, split em. However not...

    You should do it right, split em. However not gonna say I didn’t JB weld a bad case on my 1992 CBR600 commuter 21 years ago that held up well enough to last me till I sold it 6 months later. In...
  3. Replies
    61
    Views
    3,189

    Good write up man, I’ll definitely be keeping...

    Good write up man, I’ll definitely be keeping your grounding techniques in mind during my current build.
  4. Man the whole time your watching you just keep...

    Man the whole time your watching you just keep saying someone look up and notice this fuckin inferno for christ sake
  5. You had me at next bike considering the beaut you...

    You had me at next bike considering the beaut you built this last time, do you really have another in mind?
  6. Best forklift video ever

    Best forklift video ever
  7. I finished cleaning and sorting out the side...

    I finished cleaning and sorting out the side cover on my ratchet top. When I pulled the cover the studs came out easy breezy. It’s an STD case and I’m assuming whoever installed the studs didn’t...
  8. Replies
    61
    Views
    3,189

    SteveJ you should consider doing a write up on...

    SteveJ you should consider doing a write up on wiring under the how-to section. Sounds like you have quite a bit of time under your belt and I’m sure it’d be an invaluable tool for many builders.
  9. For the most part you got it. I mean don稚 forget...

    For the most part you got it. I mean don稚 forget replacing seals while you at it as well as the possible need to go with a heavier weight fork oil depending on how you like your forks to feel,...
  10. $1500 clean title in hand. All original outside...

    $1500 clean title in hand. All original outside of air cleaner, rear fender/tail light, speedometer, tachometer, and seat. I’ve started cleaning her up a bit and ordering the correct parts. I should...
  11. Thanks Doom, I’ll definitely give it a watch...

    Thanks Doom, I’ll definitely give it a watch tonight. I figured out that flake of metal I found was just part of a sheared stud, which I’m replacing anyhow. Everything looks clean though outside of...
  12. When I pulled the kicker cover I checked for...

    When I pulled the kicker cover I checked for shavings, everything looks good so far besides this one little piece of metal, almost looks like a bolt thread left behind but can’t identify it or find...
  13. On to the 4 speed. This is my first go with a 4...

    On to the 4 speed. This is my first go with a 4 speed ratchet top, so I’ve found as many manuals and videos as possible to ensure I get this right and proper, I’d like it to see many miles.
    ...
  14. Replies
    38
    Views
    1,199

    Who knows the dude who might stumble upon it in...

    Who knows the dude who might stumble upon it in the future and need that advice, knowledge sharing is always a good thing. Thanks for the type up Doom.
  15. https://monstercraftsman.com/ Monster Craftsman,...

    https://monstercraftsman.com/
    Monster Craftsman, I have one of their weld on chain tensioner’s on my XS650, they also sell all the parts if you need to repair yours, haven’t had any trouble with...
  16. Still moving along. I picked up a GMA rear brake...

    Still moving along. I picked up a GMA rear brake setup with 11.5” rotor and snagged up a GMA 5/8” rear master cylinder as well. 108384 My daughter lost all interest after getting through the bubble...
  17. Replies
    459
    Views
    40,268

    Aircraft stripper works but takes a lot of elbow...

    Aircraft stripper works but takes a lot of elbow grease and time, at least all the off the shelf shit I’ve ever used. Why not just get it sand blasted or soda blasted, small piece and shouldn’t take...
  18. Replies
    28
    Views
    993

    Hard to make a call, have to agree with...

    Hard to make a call, have to agree with TriNortChopz as in nothing that discerns it from many others. The 17 digit serial # is a present feauture on everything from Daytec to Ultima frames and even a...
  19. Replies
    1,470
    Views
    204,360

    Such a beautiful build amigo, hope you get a...

    Such a beautiful build amigo, hope you get a great price for it.
  20. Haha man this thread was from like 5 years ago....

    Haha man this thread was from like 5 years ago. It was on a 2001 XL. 4 over=4 over stock, so add 4 onto your brake line and your set. The easiest way to do this, incase you don稚 have a stock...
  21. State Farm has been good by me all these years,...

    State Farm has been good by me all these years, even with claims on home and auto. I shop around every 2 years or so as well and they always stay competitive or better.

    Although I知 sure your...
  22. Replies
    6
    Views
    471

    I had a few buddies make the run last year from...

    I had a few buddies make the run last year from northern IL, few shovels and chopped evo sportsters. Everyone made it back and it should be mentioned a strong mechanical inclination was possessed by...
  23. If your jets are gummed up it will still run on...

    If your jets are gummed up it will still run on starting fluid as your bypassing the carb. Are you getting a good spray when you manually twist the throttle? Did you check your vacuum lines for...
  24. Did you pull and clean the Jets when you cleaned...

    Did you pull and clean the Jets when you cleaned your carb or just kind of carb clean spray it out? Gas is shitty and I clean the jets with fine wire yearly at the beginning of the season on my...
  25. Absolutely stunning job Doom, everything is on...

    Absolutely stunning job Doom, everything is on point, and the detail you put in really tied it all together. Hopefully I can see it in person this summer if ya got the time.
Results 1 to 25 of 164
Page 1 of 7 1 2 3 4

Log in

Log in