CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: HogsRear

Page 1 of 3 1 2 3

Search Forums: Search took 0.01 seconds.

  1. Replies
    24
    Views
    1,047

    Thank you Jim! I figured it's there for a reason,...

    Thank you Jim! I figured it's there for a reason, but right now it's definitely blocked. I believe this is the enricher side. I blew it out with compressed air and have been poking at it with a pick...
  2. Replies
    24
    Views
    1,047

    Potentially dumb question. I picked up another B...

    Potentially dumb question. I picked up another B for cheap so I figured I would clean it out and see if it was any different. Are these two holes in the bowl supposed to connect? The other side of...
  3. Replies
    24
    Views
    1,047

    I actually made a pair with hardware I had laying...

    I actually made a pair with hardware I had laying around and installed them in some new pipes today. I currently have them at a 90 degree angle in the pipe but maybe I should try tilting them a bit...
  4. Replies
    24
    Views
    1,047

    Alright I ordered a set of smaller drill bits and...

    Alright I ordered a set of smaller drill bits and will try opening up the main air bleed to .060 – also planning on trying the lollipop in the pipes trick. I'll check back in once I get it together....
  5. Replies
    24
    Views
    1,047

    [QUOTE=Dragstews;846396] :confused: what?

    :confused: what?
  6. Replies
    24
    Views
    1,047

    Thanks Drags. I haven't seen this Power Tube...

    Thanks Drags. I haven't seen this Power Tube before, have you used one with relative success? They are making it sound like the greatest invention since sliced bread.
  7. Replies
    24
    Views
    1,047

    Thanks Jim. I was surprised when I replaced the...

    Thanks Jim. I was surprised when I replaced the shaft there was virtually no play at all, in fact it went in a bit tight and then was able to spin smoothly once fully assembled. I would have a hard...
  8. Replies
    24
    Views
    1,047

    S&S Super B Mid Range Flat Spot Shovelhead

    I recently picked up a used Super B and wanted to try it out on my bike. It's a kick only stock displacement 74" shovel chopper with points ignition. Timing is good, and seemingly no intake leaks...
  9. Replies
    20
    Views
    1,064

    Not really honestly. I cleaned it and checked...

    Not really honestly. I cleaned it and checked everything with the butterfly and it all looked good. The carb is clean and I double checked all the little pieces. Put it all back together with new...
  10. Replies
    20
    Views
    1,064

    I'm able to wiggle it a tiny bit, and there's no...

    I'm able to wiggle it a tiny bit, and there's no resistance sliding it in and out of the carb body. You think that could be it?
  11. Replies
    20
    Views
    1,064

    I have the carb apart right now but the throttle...

    I have the carb apart right now but the throttle shaft is still in place. Do I pull it out to check the bushings?
  12. Replies
    20
    Views
    1,064

    Nope, stock bore just refreshed. If it ends up...

    Nope, stock bore just refreshed. If it ends up not being an intake leak (a friend pointed out the clamps I have aren't that good of quality) I will check the springs again but I took a look the other...
  13. Replies
    20
    Views
    1,064

    Haven't adjusted pushrods or re-torqued heads yet.

    Haven't adjusted pushrods or re-torqued heads yet.
  14. Replies
    20
    Views
    1,064

    Totally makes sense, and I hear you on the simple...

    Totally makes sense, and I hear you on the simple solutions thing. It's a hard lesson learned sometimes. I don't think it's the cable because I am able to physically look into the mouth of the carb...
  15. Replies
    20
    Views
    1,064

    I guess I should have mentioned early on that the...

    I guess I should have mentioned early on that the throttle cable was one of my first checks each time I run it and it’s not causing the issue. It’s a new cable and I make sure I am press it closed...
  16. Replies
    20
    Views
    1,064

    Yes stock point ignition, everything recently...

    Yes stock point ignition, everything recently replaced when motor was rebuilt but I will look anyways.
  17. Replies
    20
    Views
    1,064

    Thanks Abbandon. I'll try the test with carb...

    Thanks Abbandon. I'll try the test with carb cleaner next. I can't remember exactly but when I rebuild the carb I only replaced a couple pieces because it was clean and in pretty good shape, and I'm...
  18. Replies
    20
    Views
    1,064

    Shovelhead w/ Super E Hanging Idle After Rev

    Hi all, I've spent some time trying to diagnose this problem and I'm looking for some second opinions. Bike is a freshly rebuilt 1973 Shovelhead chopper with Super E carb, kick only, belt drive,...
  19. Replies
    32
    Views
    1,769

    Good call, I checked when the bike was cold. Will...

    Good call, I checked when the bike was cold. Will check again. Bike is at my buddy's house so I haven't been able to go over it yet. I should have mentioned that all of the wiring is stripped down...
  20. Replies
    32
    Views
    1,769

    Interesting, I guess this could be what's...

    Interesting, I guess this could be what's happening. I checked my pushrods when I changed the points a couple weeks ago and everything seemed fine (not loose, but still able to spin them in my...
  21. Replies
    32
    Views
    1,769

    Yes and yes.

    Yes and yes.
  22. Replies
    32
    Views
    1,769

    It tested ok not running but I wanted to switch...

    It tested ok not running but I wanted to switch to a sealed battery that fits in the oil bag a little better anyways so I will keep the old one as backup.
  23. Replies
    32
    Views
    1,769

    Alright I have ordered a new sealed battery to...

    Alright I have ordered a new sealed battery to replace the current lead acid battery I got from NAPA, hoping that it helps. Going to look over the wiring this weekend and see if there are any weak...
  24. Replies
    32
    Views
    1,769

    Tank vent seems to be working fine, no difference...

    Tank vent seems to be working fine, no difference in performance with gas cap off while running
  25. Replies
    32
    Views
    1,769

    Another thought related to that – if it were a...

    Another thought related to that – if it were a short, wouldn't this cause the bike to immediately shut off rather than a slow decrease in performance, misfiring and popping over the span of a few...
Results 1 to 25 of 65
Page 1 of 3 1 2 3

Log in

Log in