Search Forums:

I would give it a blast of brake cleaner followed with a light blast of compressed
air (maybe 30 psi) then repeat. then I would rub some (red) silicone sealant into the crack.
after it dries, I...

Did You try to adjust the idle mix screw? When the intermediate jet is changed, The idle screw
usually needs to be fine tuned to get the correct amount of air for the mixture.

S L O W IS G O O D


<iframe width="560" height="315" src="https://www.youtube.com/embed/iyne4emfrc0" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay;...

The Idea was for the "worn out" Big bore cases to be hard coated, not the stock bore ones,
YOU Dumbed Down IDIOT.

that is a good deal. that is the same oil that I have been using for the last 5 years or so.
I think I paid over 7 bucks a Qt about 6 mo ago.

^^ THIS is what I was going to recommend. have the Cylinders Hard Chromed or Nikasil coated, Then re bore
them. I have never done this with Harley Cylinders, But I have had jugs coated for...

Yep, I remember those bird deflectors, I could not remember the name. Landstroms, It's
been years since I checked out His web sight. such a boss Deflector

At least the bike does not have a hugemongus tire on the front end.

I know a dude that has one of those exile chops that started out with a 230mm rear &
a 300x21 on the front.
One day He...

Doom... Is the 1/4" fuel line all new, or have You run it before on that bike?

The copper tubing may be 1/4" i.d. But the fittings are likely to have a
smaller i.d. & could be restricting...

Could be the pump. try fiddling with the acell pump, & even consider taking a
look at the pump diaphragm, a make sure it is not compromised. (dried out
or compressed, cracked, etc. )

"You want to believe"?

Dude.... The vote rigging has been going on for many years, That's what happens when a
Country gets infiltrated with Fascist Rats that will stop at nothing to ram Their...

108243

I rode on the 3rd el Diablo back in 2008. that's the only one I did.
back then, the Route went south to San Felipe (2 nights), 3rd day was a ride across
the desert to Ensenada for 1 night, & last...

The Global Death Cult




108238

Pretrial transcript laying it out

https://www.brighteon.com/a5be543f-b148-4804-9e1c-536efa46164b

It looks like the covidian death cultists (perpetrators of the covid scam demic) could be
heading for a trial in the future for their crimes against humanity.
I'm not holding my breath though,...

Check out American Prime Engineering.

I got a belt from them awhile back and the quality looked considerably
better than the stock primo belt it replaced.
Made in USA of course.

Dusty, I don't know how bad off your son is, But I have a cousin who
had multiple cancers ( melanoma & various organ cancers)
& chose to avoid the common chemotherapy approach, &
Instead opted to...

Rogan is a semi clueless newbie trying to be like alex jones.

I will give Him credit on refusing the main stream health narrative that is
owned & controlled by the...

That is great that Jim's son is continuing the legacy.

A good friend of mine who is now gone, was good friends with Ed Iskenderian
the Camfather (of automobile cams) & My buddy, a few years back...

Brooker from Procol harem & Mark Lanegan both slipped away today.

This piece here is probably my favorite recording of Lanegan
He was featured on this Mad Season tune (Slip Away).
& Mike...

aw man. I consider Jim the camfather of m/c cams. (no disrespect to Isky)
I hope someone continues His legacy & keeps the grinders going, His cams rule.

I just modified a fuel tank using silicone bronze. I relocated the petcock outlet/bung,
& blocked off two redundant outlet/bungs.
Afterwards, I filled the bath tub with water & used a shop vac...

I never seen the Hemi U G run at the drags, But I have loved that car
since about 1969 when I assembled a Revel plastic model of that car when I
was a kid. The Little red wagon was at allot of...

how about drilling the back of that seat & installing some rivet nuts


https://www.mcmaster.com/nuts/rivet-nuts/sealing-screw-to-install-rivet-nuts/

Those ones in the link are only 1/4" But 4...