CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: shank1kole

Page 1 of 9 1 2 3 4

Search Forums: Search took 0.22 seconds.

  1. Replies
    5
    Views
    155

    Im going the chop route ! The frames were...

    Im going the chop route !
    The frames were twisted with a lot of work to get right.
    leafer front end. got an old paughco frame to cut up.
    The little Aisn 300 blower is perfect ,plan is to run a...
  2. Replies
    5
    Views
    155

    going to look at servi frames

    Hello all
    I recently traded an S&S/HD mixed parts shovel for a 65 G motor(flathead 45) with title.The fella I got the engine from has 2 servi frames I'm going to look at.
    Im going to check for...
  3. Replies
    29
    Views
    2,210

    Thank you for the heads up on the electronic...

    Thank you for the heads up on the electronic ignition Montuckymatt!
    Just got my first flathead and I am building a parts list. I am leaning towards a supercharger on my unit, and that ignition...
  4. Replies
    185
    Views
    24,807

    working on the pipes.

    working on the pipes.
  5. Replies
    45
    Views
    8,555

    They come up every year herein SE michigan. If...

    They come up every year herein SE michigan. If anyone wants to gather some,I will post when they pop up this year. Had over 500 last year in the fence rows, its an amanita mascaria version all over...
  6. Replies
    69
    Views
    13,641

    Damn it man! you rolling in some bad luck lately!...

    Damn it man! you rolling in some bad luck lately!
    Get out the manual CALMLY
    remove head Calmly
    re install and check everything as you go.

    As for electrical, more than half the...
  7. Replies
    185
    Views
    24,807

    Turbo is here.

    Turbo is here.
  8. Beautiful work ! be proud in your style and...

    Beautiful work !
    be proud in your style and knowledge!
  9. Replies
    185
    Views
    24,807

    Got a Garrett turbo in the wind, along with a...

    Got a Garrett turbo in the wind, along with a piece of unicorn horn (Mr Turbo manifold), also picked up an ARD magneto for this girl. She has sat due to a busy life, but about to be unleashed again...
  10. Replies
    12
    Views
    917

    Air hammer with steel and brass washers. the ease...

    Air hammer with steel and brass washers. the ease will amaze you. something about the hits per minute ha ha. Be well.
  11. Poll: Hey Drags, got any frames left? perhaps with a 45...

    Hey Drags, got any frames left? perhaps with a 45 degree rake? for the "hair dryer" build we have began speaking about
  12. Replies
    5
    Views
    1,102

    Righteous!

    Righteous!
  13. Replies
    185
    Views
    24,807

    Well the site crash is a downer. Here is a pic...

    Well the site crash is a downer.
    Here is a pic of my girl, getting real close to firing her up.
  14. Replies
    185
    Views
    24,807

    Thanks for the kind words all.I put a thread...

    Thanks for the kind words all.I put a thread rating at ok let me know if I'm wrong.I used HOK concentrate added to clear, and wow it goes a long way.I used14 ounces of clear and about fifty drops of...
  15. Replies
    17
    Views
    2,809

    Bad ass mo fo !

    Bad ass mo fo !
  16. Replies
    185
    Views
    24,807

    Yes, there is more.

    Yes, there is more.
  17. Replies
    185
    Views
    24,807

    Part two

    Part two
  18. Replies
    185
    Views
    24,807

    the other two.

    the other two.
  19. Replies
    185
    Views
    24,807

    Here is the start, this was about 5 hours of work...

    Here is the start, this was about 5 hours of work to get these lines and airbrushing done.I bet another 5, then 5 hours on Kandy/lines.The area I'm pointing at is going to be re designed.
  20. Replies
    19
    Views
    1,996

    oven cleaner, strips a lot of finishes but have...

    oven cleaner, strips a lot of finishes but have water hose ready to deactivate it.About a 5 second sit strips any loose gunk. maybe silicone the gasket areas strip clean then pull silicone and hand...
  21. Replies
    185
    Views
    24,807

    I ran tape lines for two hours and only confused...

    I ran tape lines for two hours and only confused myself, I'm going to have to run large scale sample for sure.Car hoods are a solid plan.
  22. Replies
    13
    Views
    1,140

    I run two sets of dryers with one regulator, but...

    I run two sets of dryers with one regulator, but I have drop tees with butterfly valves(to let out moisture/contaminents) every 15' or so along my 100' cast iron pipe.The drop tees get about a half a...
  23. Replies
    185
    Views
    24,807

    Had to put it together to look at the lines...

    Had to put it together to look at the lines again.I got it knocked down ready for lines so it looks grayish right now.I have used JobLine epoxy primer, base ,and clear all to there specs and got...
  24. I was scraping one time, and came across a true...

    I was scraping one time, and came across a true ton of military surplus rifle parts.Even had some M1 carbine receiver castings about 80% I shit my pants, spent a $500 that day(buying it from the...
  25. Replies
    185
    Views
    24,807

    Thanks Hatchet I have tried out a few...

    Thanks Hatchet I have tried out a few patterns while in primer, but have not locked down much.Im leaning towards Brandywine,cherry red,and yellow gold Kandys. But once I start taping lines who...
Results 1 to 25 of 221
Page 1 of 9 1 2 3 4

Log in

Log in