CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ExplodingCoffinEmporium

Page 1 of 10 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    745
    Views
    45,327

    Damn good coating, I run that or chasis saver...

    Damn good coating, I run that or chasis saver based on what痴 getting covered and have never had a disappointment over the years. If I get it on the rotisserie it痴 getting coated as I知 not in the...
  2. Replies
    13
    Views
    306

    Easy breezy for ya, either take a digital caliper...

    Easy breezy for ya, either take a digital caliper and measure everything or pull the parts numbers off your bearings (which will be printed on them) and plug them into google to get your dimensions...
  3. Replies
    13
    Views
    306

    Sportster front wheels have a variety of sizes,...

    Sportster front wheels have a variety of sizes, 3/4”, 1”, and modern comes in 25mm. You need to clarify things a bit as you say the axle doesn’t fit you’re narrow glide, so does that mean you don’t...
  4. Replies
    4
    Views
    111

    I mean seems legit, albeit a little dated, but...

    I mean seems legit, albeit a little dated, but nothing is out of place. The certificates all check, no bad marks or spam issues, no reports coming back negative. Prices are in line with the market as...
  5. Replies
    745
    Views
    45,327

    Any chances on showing your fin repair process?...

    Any chances on showing your fin repair process? Thanks for taking the time to post all this up Dragstews, I enjoy following along on your engine work.
  6. As long as everything is within spec you...

    As long as everything is within spec you shouldn’t need any shim(s). You should have seals, bearings, spacers, and a lock nut washer. Set preload properly and your off to the races.
  7. Looks great Alfajuj, thanks for sharing

    Looks great Alfajuj, thanks for sharing
  8. Replies
    12
    Views
    476

    I’m assuming it has a clean title correct? If so...

    I’m assuming it has a clean title correct? If so that thing looks like it was stored rough and will need a good going through to say the least. Being a midwesterner I’m not much scared by rust but...
  9. Possible dilemma I hadn’t considered, will a...

    Possible dilemma I hadn’t considered, will a 1965-78 transmission fit in a dropseat frame without modification or case change? I put her in without bolting her down but the alignment doesn’t seem...
  10. In typical fashion of not leaving well enough...

    In typical fashion of not leaving well enough alone, I decided a frame swap was due mid build, and this came in the form of a dropseat frame with windowed neck and mild up and rake. I also snagged a...
  11. Replies
    13
    Views
    306

    If the hub is 3-9/16” from bearing to bearing...

    If the hub is 3-9/16” from bearing to bearing then yes it will fit a narrow glide. OEM hubs which varied in thickness throughout the years are wider than what your are trying to run.
  12. 6’2”, forward controls definitely needed, but...

    6’2”, forward controls definitely needed, but I’ve put 1000’s of miles on sportster(s) without an issue. I wouldn’t ride from Chicago to California but that’s more based on ergonomics and comfort...
  13. Well the threaded hole is for an oil return line...

    Well the threaded hole is for an oil return line which travels to the breather gear hole but in my case a plug is in order. Waiting on parts to come in as cylinders are out for powder coating, tons...
  14. Cleaning up everything. Delrkon case with the...

    Cleaning up everything. Delrkon case with the bottom trap door which is unsurprisingly leaking a bit. I’ll give it a good cleaning, attempt to ensure surface area is as flat as possible, and seal the...
  15. 109338 Unknown to me engine with good...

    109338

    Unknown to me engine with good compression. I’m getting the cylinders deglazed and powder coated while freshening up the heads, rocker boxes, and going through everything with a fine tooth...
  16. 109283109284109285109286109287 Getting this...

    109283109284109285109286109287

    Getting this crazy frank style rear fender dialed in, still haven稚 decided on a paint scheme but got plenty of time.
  17. Replies
    3
    Views
    502

    Looks like a stock rake on a dropseat frame with...

    Looks like a stock rake on a dropseat frame with extended forks, hence engine sitting high on the front, crazy frank yessum.
  18. Replies
    745
    Views
    45,327

    That is interesting, got my attention.

    That is interesting, got my attention.
  19. Looking forward to the thread man keep on truck’n

    Looking forward to the thread man keep on truck’n
  20. Replies
    480
    Views
    46,766

    No shit, be curious to see what it looks like...

    No shit, be curious to see what it looks like when your done.
  21. Replies
    745
    Views
    45,327

    Yeah I知 sure you will, people who weather the...

    Yeah I知 sure you will, people who weather the storms with us become a part of our own fabric, you don稚 just lose a person, you feel like you lose a little of yourself in some ways. It always...
  22. Replies
    745
    Views
    45,327

    Sorry to hear that Dragstews. I’d always assumed...

    Sorry to hear that Dragstews. I’d always assumed the “Drag” in your name reffered to drag racing. None the less, hope your holding up ok.
  23. Replies
    5
    Views
    450

    Yeah hard to argue with that, if it ain’t broke...

    Yeah hard to argue with that, if it ain’t broke don’t fix it or else who knows what can of worms you may open in doing so.
  24. Replies
    5
    Views
    450

    Interesting, I run the BDL Competitor CC-100-S on...

    Interesting, I run the BDL Competitor CC-100-S on my 78’ and it’s 7 steel and 5 friction, starts with 2 steel then fiber alternated until ending with steel.
  25. I’ve never done it on a mag, but have had decent...

    I’ve never done it on a mag, but have had decent results with pushing out some dings of that magnitude with my hydraulic press and some wood blocking for support, it’s a slow steady process but it’s...
Results 1 to 25 of 247
Page 1 of 10 1 2 3 4

Log in

Log in