CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Whoremonger

Page 1 of 12 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    16
    Views
    628

    I made one out of scrap parts. Works great for...

    I made one out of scrap parts. Works great for heat cycles, fixing oil leaks, setting timing, checking charge system. Tried for an hour to upload pics. Was unsuccessful
  2. Replies
    16
    Views
    611

    If in fact your motor does have 1/4 24 screws...

    If in fact your motor does have 1/4 24 screws make sure thats what you get from where ever you source them. Very easy to confuse them with 1/4 20. Use a thread gage if possible to confirm
  3. Replies
    8
    Views
    955

    If they are titled already,they should be in the...

    If they are titled already,they should be in the clear, no? Unless they try to resell?
  4. Replies
    10
    Views
    779

    I would worry more about the shoes to the twin...

    I would worry more about the shoes to the twin cam chain tensioners. They have been known to grenade a motor when worn out. I think recommended service is 45k miles. Not sure exactly what years this...
  5. Replies
    7
    Views
    781

    All good advice, i would just add that rotational...

    All good advice, i would just add that rotational play should also be checked and corrected if needed.
  6. Replies
    27
    Views
    1,885

    The regulator of the charging system needs to be...

    The regulator of the charging system needs to be matched to the battery being used. I.e. small battery, low current regulator, big battery higher current regulator. Before you start replacing parts,...
  7. Replies
    13
    Views
    1,146

    Not sure if these are the same Cometic MLS you...

    Not sure if these are the same Cometic MLS you mention Jim , but i have some cometic gaskets for the heads and cylinder bases on my 63 pan built as close to stock specs as possible.so far they are...
  8. Has a nice stance . Cool bike!

    Has a nice stance . Cool bike!
  9. Back in 1974 i was sitting in l a county jail for...

    Back in 1974 i was sitting in l a county jail for some traffic ticket warrants i had on me. Back then i had a low rider with hydraulic lifts. They were a new thing back then and the lapd would always...
  10. Replies
    2
    Views
    425

    Cant help you with manufacturer but will say its...

    Cant help you with manufacturer but will say its a nice looking frame. Could make a nice looking and riding chop. The plates covering the rear axel holes is a bit puzzling but not hard to remedy....
  11. The repairs i have done with silicone bronze tig...

    The repairs i have done with silicone bronze tig brazing were on hairline fracture leaks. Sealed well. I would not hesitate to use it for more serious repairs on gas tanks. If im not mistaken,...
  12. Replies
    2
    Views
    391

    Thanks Jim

    Thanks Jim
  13. Replies
    2
    Views
    391

    Seated rings

    Took the rear head off 63 pan. Done rings about 300 miles ago. Also put some time on bench starter before mounting in bike frame.New rings are moly, cylinder oem 63 harley. Did plateu hone with...
  14. Replies
    8
    Views
    881

    The frame is HD dropseat frame so its pre 1965....

    The frame is HD dropseat frame so its pre 1965. They are nice frames. Sit lower in the seat.
  15. I had the same problem. Fixed with a new copper...

    I had the same problem. Fixed with a new copper washer
  16. Replies
    19
    Views
    1,260

    I could be wrong to me it looks like welding was...

    I could be wrong to me it looks like welding was done on the right side of the timing hole and continued onto vin pad.
  17. Replies
    25
    Views
    4,285

    Coming along nicely. Good idea about opening...

    Coming along nicely. Good idea about opening motor.
  18. Replies
    19
    Views
    1,553

    There used to be a man here in los angeles by the...

    There used to be a man here in los angeles by the name of JUNGLE JIM. he had a HUGE warehouse full of old harley parts,motors, frames,trannys, rare moldins. Basically had anything you needed for old...
  19. Replies
    6
    Views
    479

    I always try to apply the driving force in...

    I always try to apply the driving force in location of lower picture, Less chance of distorting the metal part of the seal
  20. There is a difference. Been on a 16 up front...

    There is a difference. Been on a 16 up front rigid/ springer for last few years. Never had a 21 on but have riden a couple of bikes that did. 16 does feel a little more sure footed in the turns.
  21. Replies
    14
    Views
    2,065

    This is not the same as the one i got. This look...

    This is not the same as the one i got. This look alot more user friendly . Wish i knew about it before i installed the one i got.
  22. Replies
    14
    Views
    2,065

    I have one of those adjusters. They work great...

    I have one of those adjusters. They work great and help preserve tranny cases but a HUGE pain to adjust
  23. Replies
    5
    Views
    697

    Aahhh yes you are so right jim! As a matter of...

    Aahhh yes you are so right jim! As a matter of fact i own one ! 1978 low riderůman i can be one dumb motherfucker sometimes😵*💫🥴
  24. Replies
    8
    Views
    908

    Intake manifold leak.

    Intake manifold leak.
  25. Replies
    5
    Views
    697

    What year did shovels come with 3 1/3 gallon...

    What year did shovels come with 3 1/3 gallon tanks? Never seen any myself
Results 1 to 25 of 280
Page 1 of 12 1 2 3 4

Log in

Log in