CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ncmc47

Page 1 of 6 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    79
    Views
    5,410

    What length springer did you go with? Looks good!

    What length springer did you go with? Looks good!
  2. Don't use an impact!

    Don't use an impact!
  3. Replies
    3
    Views
    262

    They are de-raked by 3 degrees,

    They are de-raked by 3 degrees,
  4. Replies
    5
    Views
    312

    Gary from Chopper Builders Handbook can probably...

    Gary from Chopper Builders Handbook can probably help you.
  5. Replies
    4
    Views
    323

    Looks to be an old Servi-car frame, before it was...

    Looks to be an old Servi-car frame, before it was robbed of it's rear legs.
  6. Replies
    32
    Views
    2,410

    I would have it x-rayed before I started chipping...

    I would have it x-rayed before I started chipping Bondo off, a trade school may be able to do for a reasonable fee. If the x-ray showed something suspicious, only then would I start chipping.
  7. Replies
    79
    Views
    5,410

    There are people who can put hallmarks on, VTwin...

    There are people who can put hallmarks on, VTwin even sells them on a sheet.
  8. Replies
    79
    Views
    5,410

    Well Dragstews said it was like the 28 degree...

    Well Dragstews said it was like the 28 degree neck but with 30 degrees of rake, I guess I've never had a 28 neck. Seen pictures but didn't think they looked that much different. So how similar does...
  9. Replies
    79
    Views
    5,410

    How does that neck look compared to an original...

    How does that neck look compared to an original 30% non-bull neck?
  10. Replies
    2
    Views
    211

    One of the chopper places sells a frame kit or...

    One of the chopper places sells a frame kit or hardtail kit, maybe Lowbrow. Also there is somebody on Ebay selling replacement tubes for rigid frames. Richard from Wasco has made pieces for me.
  11. Replies
    8
    Views
    650

    1/8" or so. Any thicker would be more noticeable...

    1/8" or so. Any thicker would be more noticeable and that's the thickness of tube you're reinforcing.
  12. Replies
    8
    Views
    650

    I think I would find a piece of tubing with the...

    I think I would find a piece of tubing with the I.D. of the O.D. of the top tube and slit it and weld onto the top tube. You could make it however long as would would fit nicely on the frame. Maybe...
  13. Replies
    3
    Views
    446

    To me it looks like an old Santee, don't think...

    To me it looks like an old Santee, don't think they are still in business.
  14. Replies
    19
    Views
    1,001

    But it was a large bend radius, not particularly...

    But it was a large bend radius, not particularly helpful for a smaller bend radius.
  15. Replies
    19
    Views
    1,001

    I would not buy that Amazon set with out further...

    I would not buy that Amazon set with out further research into CLR of dies available. Those die look like a very big bend radius, not especially helpful for a motorcycle frame. I would think a 3"...
  16. Replies
    2
    Views
    333

    Overbearing by Bare Knuckle Choppers, IIRC!

    Overbearing by Bare Knuckle Choppers, IIRC!
  17. Replies
    31
    Views
    1,681

    Those back legs look like Ford Radius rods. The...

    Those back legs look like Ford Radius rods. The piece at the bottom is solid and welded to the tapered piece. It can safely be thinned slightly. The front leg is probably also solid, and can be...
  18. Replies
    79
    Views
    5,410

    Do they make a 30 degree nonbull neck?

    Do they make a 30 degree nonbull neck?
  19. Replies
    79
    Views
    5,410

    Since that appears to be a late 47 frame, it's...

    Since that appears to be a late 47 frame, it's worth holding on to.
  20. Replies
    18
    Views
    687

    47 frames can be either 30 degree bull neck or 30...

    47 frames can be either 30 degree bull neck or 30 degree non-bull neck, with change thought to be around 7,000 serial number. I have a frame less 100 off from 7,000 so I believe it to be true. ...
  21. Do you have the right sprocket? Turned the right...

    Do you have the right sprocket? Turned the right way? I had an oring chain that cleared everything.
  22. Thread: Essential Tools

    by ncmc47
    Replies
    14
    Views
    1,832

    Take flannel shirts of the list! Very flammable,...

    Take flannel shirts of the list! Very flammable, even grinding can set them on fire. And I've got the scars on my belly to prove it!
  23. Replies
    2
    Views
    482

    I remember a similar story in EasyRiders years...

    I remember a similar story in EasyRiders years ago.
  24. Replies
    31
    Views
    1,152

    You didn't say what type of springer your using. ...

    You didn't say what type of springer your using. An inline springer has about 3 degrees more rake than the offset springer which was actually deraked 3 degrees. I would try the cups, especially if...
  25. Replies
    7
    Views
    520

    Could probably do a top end job for what that...

    Could probably do a top end job for what that costs!
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4

Log in

Log in