CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ncmc47

Page 1 of 6 1 2 3 4

Search Forums: Search took 0.11 seconds.

  1. That gooseneck pictured above is Little Freddie...

    That gooseneck pictured above is Little Freddie Hernadez of Mullin's Choppers fame. I've seen pictures of him doing a u-y in an intersection, with the front wheel making the turn and the rear wheel...
  2. Usually a few taps with a small hammer, will...

    Usually a few taps with a small hammer, will dislodge the race for the ball bearings. As far as converting the lower stem for Timkins, I'm not sure. Years ago, I spent a couple evenings with a file...
  3. I was a dealer for Nostalgia Cycle back in the...

    I was a dealer for Nostalgia Cycle back in the 80's and 90's. They had brake pedals on sale, chrome for $5.00 ordered some. When they came, one was very rusty, and I returned it. Later I ordered a...
  4. Replies
    6
    Views
    879

    And the American bike forum

    And the American bike forum
  5. Replies
    6
    Views
    879

    Take a look at the Tech forum

    Take a look at the Tech forum
  6. Replies
    7
    Views
    1,105

    I would send those pics to the mfg. Since you...

    I would send those pics to the mfg. Since you followed the directions to a T, I would like them to explain what went wrong.
  7. Very nice, great job!

    Very nice, great job!
  8. Replies
    12
    Views
    1,888

    Mufflers aren't for backpressure, they are to...

    Mufflers aren't for backpressure, they are to quiet your exhaust. I don't know who started the rumor you have to have backpressure to run right. A motor runs best with no back pressure, that's why...
  9. Replies
    6,085
    Views
    3,806,127

    Would be a bitch getting those seams straight!

    Would be a bitch getting those seams straight!
  10. Replies
    46
    Views
    4,846

    You believe what you want, around here most 8...

    You believe what you want, around here most 8 year olds know you don't point a gun a gun towards anyone and you don't place your finger on the trigger until you are ready to shoot.
  11. Replies
    46
    Views
    4,846

    Everyone should know to always check a gun to see...

    Everyone should know to always check a gun to see if it's loaded, even if the 10 other guys in the room checked it before it was given to you! If he wasn't such a libtard he would have known. He...
  12. Replies
    746
    Views
    45,832

    Say, would you list again what splined sprocket...

    Say, would you list again what splined sprocket shaft to run when using Knuckle Works left side case to short shaft tranny? With posts missing I can't scroll back and find it.
  13. Replies
    746
    Views
    45,832

    I was going to go with a grooved pinion bearing,...

    I was going to go with a grooved pinion bearing, like used to be advertised in the old biker mags. S&S advised to only make the groove 1/2 way around. Maybe taking oil from the heads? Probably one...
  14. Replies
    34
    Views
    1,374

    Are you sure that's a 48 frame? Looks more like...

    Are you sure that's a 48 frame? Looks more like what Palmer shows a 49, machining of the ride control stud. I'm relying on memory. I don't have it open in front of me. Not that it makes any...
  15. Replies
    34
    Views
    1,374

    Yes that's what I would do!

    Yes that's what I would do!
  16. Replies
    34
    Views
    1,374

    I'm not positive what you are doing, but I'll...

    I'm not
    positive what you are doing, but I'll take a stab in the dark. If you are trying to join 1 1/8th tubing to the joint where it turns to 1" as it goes towards the rear, instead of going...
  17. Replies
    6
    Views
    608

    There was at least on after market co. selling...

    There was at least on after market co. selling necks with the number boss. Don't remember if they sold frames that way, but they would certainly look AM if they did.
  18. Replies
    9
    Views
    1,692

    Gary, can't remember his last name. Very...

    Gary, can't remember his last name. Very knowledgeable guy. I think he goes by Smiley on this forum. I believe he has contact information on his site.
  19. Replies
    8
    Views
    609

    Way back when. I used 3in1 oil in the dash pots...

    Way back when. I used 3in1 oil in the dash pots of my MG.
  20. Replies
    16
    Views
    1,259

    Use a stethoscope or even a long screwdriver to...

    Use a stethoscope or even a long screwdriver to pin point where the noise is coming from. That will tell you a lot.
  21. Replies
    9
    Views
    833

    That kicker gear looks like it has been hot.

    That kicker gear looks like it has been hot.
  22. Were the condensers burning points? That's...

    Were the condensers burning points? That's usually the first sign they're going bad.
  23. Thread: Wide Glide

    by ncmc47
    Replies
    3
    Views
    572

    These are 41mm, much like what would be found on...

    These are 41mm, much like what would be found on a 50's Harley, no part number on the sliders so not a 49 part. The sliders are fairly shiney and the chrome on the tubes doesn't look like OEM.
  24. Thread: Wide Glide

    by ncmc47
    Replies
    3
    Views
    572

    Wide Glide

    I bought a set of sliders and tubes awhile back, just assumed they were OEM. The tubes have fairly decent chrome, but appear stock length. Then it dawned on me they could be after market. The only...
  25. Thanks JBinNC, for years I've told people that...

    Thanks JBinNC, for years I've told people that engines don't need back pressure to run best, only to be laughed at.
Results 1 to 25 of 129
Page 1 of 6 1 2 3 4

Log in

Log in