CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: BoulevardTrash

Page 1 of 3 1 2 3

Search Forums: Search took 0.06 seconds.

  1. Replies
    22
    Views
    3,312

    i like valspar. it's high quality and reasonably...

    i like valspar. it's high quality and reasonably priced compared to HOK (who is owned by valspar) and PPG.
    the LVB/LVCC series of paints are real nice and the clear is super slick/high solids and...
  2. Replies
    57
    Views
    18,326

    Springer is stock length and the tank is an old...

    Springer is stock length and the tank is an old 'made in Japan' Wassell style that I retunneled and lifted a bit. Probably could have got the same look with a repop mid-tunnel one.
  3. Replies
    57
    Views
    18,326

    Yea it's one of the alternator style tin inners....

    Yea it's one of the alternator style tin inners. Got it brand new off fleabay for under 15 bucks. Had to massage it a bit to line everything up but not too bad. Leaks like a motherfucker though. Hard...
  4. Replies
    14
    Views
    5,704

    right, i know what you guys are getting at. if...

    right, i know what you guys are getting at. if that screw is too tight it will want to disengage the clutch causing it to slip.
    i disassembled the clutch prior to posting here and didn't snap a...
  5. Replies
    14
    Views
    5,704

    i agree that clutch adjustment would be the...

    i agree that clutch adjustment would be the obvious reason for slippage, but i had the adjusting nuts so damn tight and it wouldn't hold at all which makes me think it was those 'friction inhibitors'...
  6. Replies
    14
    Views
    5,704

    correct. cone shovel with a tin inner/outer...

    correct. cone shovel with a tin inner/outer primary cover. pump is NOT feeding/pulling oil to/from the primary.
    my thinking was 'if i was using the factory setup the same oil would end up in there...
  7. Replies
    14
    Views
    5,704

    shovelhead clutch help

    i've been reading up on here/other forums to try and verify my suspicion, but would be nice to have a couple opinions specific to this situation.

    was out yesterday doing a little shakedown run on...
  8. Replies
    57
    Views
    18,326

    just updating this old thread. was about to get...

    just updating this old thread. was about to get her fired up last summer but wanted to re-make a few things i wasn't happy with, so i took some time over the winter to re make the sissy bar, foot...
  9. Replies
    14
    Views
    2,842

    I don't see the need to have that harsh 90degree...

    I don't see the need to have that harsh 90degree bend in the brake shackle. why not just run it diagonally like a normal springer drum brake?
    i'd also consider having some bushings at the anchor...
  10. Replies
    0
    Views
    453

    Springer backing plate ID

    I have this chrome backing plate I want to use but I'm not sure if it is for a BT brake setup.
    It's pretty much identical to the crusty old one beside it except for the lack of the raised lip for...
  11. you're creating a headache for yourself by trying...

    you're creating a headache for yourself by trying to conceptialize an idea with parts you're unfamiliar with. first of all, i'm pretty sure the backing plate hole is larger than 3/4" because there is...
  12. Replies
    9
    Views
    1,676

    pretty sure it should be 11/16"

    pretty sure it should be 11/16"
  13. yea i hadn't considered bringing it to a brake...

    yea i hadn't considered bringing it to a brake shop to see if they would swap the port side. I assumed since these were used in jeeps that there would be an existing left/right port option for...
  14. yep, good call on that one. i'll keep looking but...

    yep, good call on that one. i'll keep looking but seems like i'll end up having to just use the left port if i want to have brakes that actually work well.
  15. just found this here. i remember reading that...

    just found this here. i remember reading that these wheel cylinders were also used in (i believe) jeeps which i'm assuming is what the years listed for application are referring to.
    ...
  16. ressurecting this thread. did anyone find the...

    ressurecting this thread. did anyone find the part number for the 1 1/8" cylinders? i need a right side port wheel cylinder and cant find what i'm looking for.
  17. yet another shovel wiring diagram... need a little help

    so, i'm just trying to figure out exactly where i need to locate my fuses. would one 30A between the reg and capacitor and one 15A for acc suffice?

    i'll be using one of the morris 'main switches'...
  18. Replies
    57
    Views
    18,326

    quick little update. just about ready to tear...

    quick little update.

    just about ready to tear it down for final welding and whatnot. All that's left to do is bottom fender mount - just gonna make em off the trans plate - and then weld on a...
  19. i'm using a squish pipe on my cone shovel. only...

    i'm using a squish pipe on my cone shovel. only thing you'll need to do is make a tab off your frame to hang the squish union. the originals hung off the mechanical brake crossover support. also, you...
  20. Replies
    57
    Views
    18,326

    I just made them off the floorboard tabs. The...

    I just made them off the floorboard tabs. The brake side pedal set up is just a stock panhead juice set up, and the clutch side I made. You can see it come where in this thread.
  21. Replies
    57
    Views
    18,326

    Yea I scrapped that idea a while ago haha. Just...

    Yea I scrapped that idea a while ago haha. Just made a mount off the frame.

    The bikes comin along, just waiting on a few odds and ends. Couple small things to make then it should be good to come...
  22. Replies
    44
    Views
    11,846

    it's nice to see that the left-half only...

    it's nice to see that the left-half only handlebar trend is starting to cath on!

    nice start for sure. just lose that dual flange front hub and you'll be rockin. curious though as to why he left...
  23. Replies
    2
    Views
    1,081

    thanks a lot man! i'm thinkin i'll get both the...

    thanks a lot man! i'm thinkin i'll get both the BBX and BBT needles after looking at the list they have. theres a local shop who are dealers for rivera so i'll order what i need this week, but...
  24. Replies
    2
    Views
    1,081

    SU i.d / rebuild help needed

    i've been trying to figure out exactly what SU carb i've got here. And also trying to figure out exactly what i need to freshin/set it up for my shovel.
    here are a few pics.
    ...
  25. yea i needed to find a point to mount a squish...

    yea i needed to find a point to mount a squish pipe. don't have the mech. crossover tab to use, and it will only be supporting the little 6" squish 'union' thing. I've got a build thread goin here...
Results 1 to 25 of 66
Page 1 of 3 1 2 3

Log in

Log in