Search Forums:

Did you try contacting Andy at Pangea? I'm sure he'd help you out. Better to buy exactly what you want.

Cal Products.

Most tanks look a bit too big.. I wanted to mount one up to my sissy bar. Saw this Honda that had one about the right size:

https://i.imgur.com/ZHm4sXV.jpg?1

I got a 0.8 gallon tank, seems...

https://www.chopperbuildershandbook.com/

https://www.dbbpshop.com/?product=410004-shovelhead-engine-2d-cad

From Easyriders mag, Tips and Tricks Vol 1

https://i.imgur.com/LAHpKyN.jpg?1

https://jamesxduffy.bigcartel.com/product/swinger-oil-tank-pre-order

Denver's frame - 4" up, 16" over Denvers springer, 53 degrees rake measured at ride height:

https://i.imgur.com/aWPpnzC.jpg

The crossover tube pictured is the stock replacement rigid Panhead one that Raceframe and others sell. 1" diameter. The 1.125" measurement refers to the bottom frame rails (rigid pan bottom rails are...

It's a good idea to install and ream the bushings after the shaft is welded in place, as the heat may warp the tube slightly.

https://i.imgur.com/I7N5Yta.jpg?1

Easy enough to do, you can use a 1" holesaw with frame on side to make cut (make sure frame is clamped down tight, go slow and use plenty of coolant). Take measurements from stock pan frame to place...

https://i.imgur.com/AWjI6U0.jpg?1

Need the hole centre height measurement shown, and offset from side of case to backside of manifold flange. For this support:

https://i.imgur.com/BzHMX0n.jpg

Hey dudes. I need a measurement on a stock stroke P series S&S Panhead motor. For a carb support bracket, from centre bolt below cylinders to bottom bolt on manifold. Height and offset, in inches.
...

This one that Arie Vee just finished looks the shit, too. Beefing up all the weak points on the original design.

https://i.imgur.com/wC7Q4oA.png

The Mullins frames are now made by Smith Process. Still look pretty good, $1800:

https://i.imgur.com/KeYXHRi.jpg

Factory Metal Works make a short kickstand and mount that works well with these frames. I used one on mine:
...

Cycle X sell some, they're $399 but good quality..

http://www.cyclexchange.net/Harley%20Page.htm

https://i.imgur.com/zGFWgit.jpg

https://i.imgur.com/7DzPN60.jpg
...

Nice work so far. Who makes the ignition setup, is that the Tri-spark one?

The original bearings (New Departure ND3203AU) aren't made anymore, unless you can find some NOS ones. The replacement bearings are 88503 (NSK or similar). 40mm OD / 17mm ID / 16.6mm wide. They are...

Here's a couple of pics to show the difference. The section of casting where the speedometer cable exits is curved in 1936 - early 1941 frames. From 1941 onwards it's a 90 degree bend (in second pic,...

The easiest way to date a frame is the number on right axle plate casting. Should read '2 XE-6' for a 1938 or 39 frame. The neck should have a forging number 'XE-35', and the number 2 or 3 for '38...

Nice work so far. If you haven't made up the manifold yet - consider extending the S&S one! A mate of mine made one for twin amals from a
two throat manifold, came out pretty nice:
...

4 up, 3 out, 22 over springer, 21/19 wheels, rake unknown (looks like about 45 degrees):

https://i.imgur.com/wRR7Oxk.jpg

https://i.imgur.com/qgrnYDX.jpg?1

They don't seal too well, is the short answer. The plastic tube is it for sealing. People who have remade them have used a different design to incorporate a proper seal at the top.

You can machine...

It's not the weight of the gas that contributes that much to instability, it's when it moves around. Offroad racing teams & fighter jets use anti sloshing foam to avoid this. And obviously the lower...