This is Robs unicorn...His shovel. He is a inland empire local who is in slimsfab quite frequently. He builds alot of evo sportys. He usually comes in for a hardtail, fender,sissybar,handlebars,oil bag,etc..This is the shovel a few posts back that he has completed after he trucked it home from the Farm. The paint was nicely finished by Rob also...It is a stange but cool feeling to see bikes on the road I have had the pleasure to do work on,These pics were taken by me at an ARCO fuel station in Hemet, Ca Slim
This super sano Ironhead was brought in to the Farm for some pipes.Mike asked for them to be inch and five eighths , for slight backpressure. then swept out with a heatshield. Thanks for stopping in Mike and family. Slim
This is a frame sent to me in the mail from New Mexic. It arrived as a Headstck and backbone.the rest was fabbed here at the farm. it is a single loop shortened out back just a bit, to get rid of the xs 650 "gap" between the engine and rear fender.Slim
This is Ralfys sportster. It is now long as FUCK. He came out and asked for a set of 40 over legs for his springer, so they are now made from 4130 chromoly.120 wall. I did not build this one from scratch. the bike got quite a bit of rake and a pitchfork sissybar too.this will be powered by a stroker Iron head. Ralfy will be building and painting the rest of his rig.SLIM 951 217 8814
This is Dereks sporty he represents San Pedro.This bike has been on the blog as you can see the last two shots are from the previous fab session. This time Derek came out he brought out some axle plates to be swaped onto his frame fabbed here at the Farm.In case you havent noticed the running gear is a sporty mill (1000 cc) with the trans hacked off connected to a early ratchet top 4 speed via inch and a half belt drive..The oil tank with stash tube,and Wish boned downtubes are a couple of nice features we also knocked out here. The pipes are fabbed by Derek and carry the lines of the bike out super nice. SLIMSFAB is now on Instagram....look up slimsfab for one off parts and some hard to find parts on the instagram page. SLIM 951 217 8814
This is a evo sportster frame Fabbed here at the Farm for the Gasser Lounge,Lady Hump,and Sailor Jerry. Mike in the far right of the picture came up with some pretty detailed specs and we handled it.It received a tight loop hardtail,3 3/8 inches of downtube stretch, a fresh back bone, 2 degrees of rake change and a slimsfab high capacity keg oil bag.Keep an eye out for this build.The guys pictured from right to left are Mike Torres, Alan from Lady Hump,Mikey from gasser Lounge,and James. I am the asshole with the camera you cant see. the last shot is a before shot! Slim 951 217 8814
This is Robs shovelhead.He came by the Farm for a hardtail ,fender,sissy bar,and to have his oil bag installed.The hardtail on this bike is stock length.The bikes battery tray is set up for an Antigravity battery(12 cell) as most of the bikes that leave here are.They are very compact and light weight with extreme power and consistency. Slim 951 217 8814
This is Soto and his looptail sportster.a few posts ago you can see his bike before he chromed the oil bag, bars and fender, built here at the Farm.He came out to hang and I fabbed him up this bad ass sissy that holds his board in place on rides to local skate spots. Soto rides this bike as primary transportation.Ride or Die Mother Fucker.Slim
Here are some shots of the Drivetrain in my van. It is powered by a big block Mopar RB engine backed up by a 727 torqueflite trans through a telescoping driveline to a 1959 Hallcraft V drive, through another telescoping driveline to a 10 bolt chevy rearend. I fabbed hard cooling lines from .095 wall mild steel mounted along the driverside framerail. The fuel tank in the pics is NOT mounted but will be soon mounted under the floor with the cap entering up through the floorboard. the sheetmetal floorwork and seat are underway and then test drives are up next, then a roof.
Subscribe
