We are forever grateful to work with talented artists like Brittney Thomas aka Bombshell Deluxe. Brittney is creating quite a name for herself by producing one-of-a-kind works of art on motorcycles, gas tanks, helmets and more. She recently reached out to see if we'd be interested in partnering with her for a giveaway. Click here for the chance to win this custom large Vega helmet. We'll announce the winner on January 24th. Best of luck!
Word has it the Appalachian Moto Jam snow hill climb has been postponed due to the impending weather conditions for this weekend. Check the site http://www.appmotojam.com/ and the Instagram for the latest updates.
Either way, get out there and have some fun in the snow this weekend!
Order Issue #7 of the brand new Kustom Kulture print publication, featuring lowbrow artists, pinstripers, sign painters, builders, hot rods, motorcycles, tattoos, humor, kustom kulture lifestyle, and more!
64 pages. Full color glossy.
INSIDE THE WINTER 2019 ISSUE: Artist Spotlight: Jeremy Pedersen
Artist Spotlight: Explo
Artist Spotlight: Jono Doiron
Vintage mask collection of Rudy Munis
Featured Artist: Kustom Artist Matt Grosso
Featured Artist: The Art of Andrew Wright
Featured Artist: Chopper and Kustom Art of Russell Murchie â€œMOWâ€
Artist Interviews Artist with Matt Lugo and Eddie Zacharek of EZ Kustoms
The Museum of Evel Q&A with Lathan McKay, co-founder of the Evel Knievel Museum
Outing to Nowhere - Part 2 Short story by "Doc" Clancy Illustration by Kevin Maginnis
Hot Rod Art by Alana Wilkie
Q&A with Ryan Meyers of Sioux Guitars by Jeff Alexander
Photos stolen from BaRon's blog and DICE Magazine. This build is really neat - about everything about it - I like it a lot . . .
I like the front wheel, rear fender, frame molding, high shoulder rims, paint color, mural . . . it's just a bitchin' build. I might shorten the sissy bar and lean it back a bit...and ditch the CV carburetor for an SU or Linkert...but, hey - it's not my bike - and I don't think it's for sale - and if it was, I probably couldn't afford it. Hats off to one sweet ride.
After repairing the engine cases, machining, measuring, etc. Almost every part on the engine has required attention. The motor was assembled when I received it, but the parts mirrored "swap meet specials" haphazardly assembled. The ball bearing construction appears easy to conquer...but now you're dealing with hand-press-fit on everything. It's very difficult to align the cam timing marks when each cam is pressed into position. There are so many particulars that need addressed when assembling an engine of this nature. Basically, it's got to be perfect, or it won't run at all. This is the 5th ball bearing-type engine I've built (with my dad too) - and we still spend about as much time reading, as we do building the motor.
The magneto is a horizontally mounted Wico Single Fire type unit. The ignition timing is best set by location of the piston to TDC...then verify the timing actual timing mark on the flywheel. On the earlier WRs, once the gear cover is on...you can't change your timing from the outside, since the magneto is bolted solid to the case. No rotation. The Wico cap has a #1 which indicates the REAR(or #1 cylinder) and the spark plug wires must be installed correctly.
I updated the sprocket shaft seal (from the steel reverse thread seal) to a modern type rubber-lip seal. The seal kit (from Colony) is the same as a Big Twin seal, since the sprocket shaft in a WR is the same diameter as a panhead....but runs the larger 25mm ID ball bearing. A #1205 ball bearing to be exact: 25mm x 52mm x 15mm Superblend-type bearing.
The lower pump has been checked over, blasted, washed and inspected. I painted it my special cast iron gray, installed, with breather timed. I bumped the breather ahead 1 tooth, since the piston was already about 2" down in the cylinder before it started opening (via timing mark). By one tooth advanced, the breather window opens just after TDC - to get that crankcase evacuated of pressurized air a bit sooner.