Another Early Pan motor Build ...

[Tattooo]

I'm wondering how it would be to run small floor boards in a forward position rather than pegs. I don't know if it would look bad on a chop or if it would function well. I haven't found a pic of it done yet. I'll probably start a foot clutch/ fwd control thread to solicite advice when I get there.

You haven't found many pics of floor boards on choppers because it looks silly.... Not being a smart ass, Just being honest....

[JeremyL]

You haven't found many pics of floor boards on choppers because it looks silly.... Not being a smart ass, Just being honest....

That's why I was asking. Thanks!

[JeremyL]

Man that is awesome.... Try and find another rear wheel like he had in the pic...... And PLEASE don't put an air ride seat on that bike..... That will kill the looks of it..... They don't ride all that bad.... Just learn what tire air pressure rides the best....

Thank you for the advice!

[Tattooo]

That's why I was asking. Thanks!

Your welcome..... You have a Damn nice looking bike..... I'd hate to see you mess it up by not knowing..... I'm really glad you don't mind asking questions....

Like I said we are here to help you....

[JeremyL]

Your welcome..... You have a Damn nice looking bike..... I'd hate to see you mess it up by not knowing..... I'm really glad you don't mind asking questions....

Like I said we are here to help you....

I'm on here to learn. I deff don't want to disrespect this bike by doing something ignorant. I can't express how much I appreciate your help!

While we're talking. Many parts of the frame have been shaved/smoothed already but the side car mount was left alone. It interfere with the pipes that are on it. Would I be making a big mistake by cutting it back???

ò

[Dragstews]

That photo shows the brake crossover shaft ... ^^^
Ya might be needing that ...

(Even Tattoo runs a rear brake)

[JeremyL]

That photo shows the brake crossover shaft ... ^^^
Ya might be needing that ...

(Even Tattoo runs a rear brake)

Oh! I'm sorry. That shaft is for mechanical brake linkage? It has a hydraulic brake system installed.

[Dragstews]

In that case, yeah hack it off..

[Tattooo]

In that case, yeah hack it off..

NNNoooooo Don't hack it off..... I really like Mechanical brakes......

[Tattooo]

Oh! I'm sorry. That shaft is for mechanical brake linkage? It has a hydraulic brake system installed.

Is your rear brake a disc or drum? It's hard to tell by your pics.... Is it a juice drum brake?????

Can we get some better pics of your frame before you start cutting one it??

[Tattooo]

That photo shows the brake crossover shaft ... ^^^
Ya might be needing that ...

(Even Tattoo runs a rear brake)

LOL I tried it for a couple of years but I did at least I did a have front brake..... One at the time is all you really need....

[JeremyL]

Is your rear brake a disc or drum? It's hard to tell by your pics.... Is it a juice drum brake?????

Can we get some better pics of your frame before you start cutting one it??

These pics aren't great but all I have at this moment. shows rear disc & caliper but not close up.

[Dragstews]

As low as that sits, the "S" pipe would be a better choice...

[Tattooo]

As low as that sits, the "S" pipe would be a better choice...

Yep you got that right.... I would drag that pipe off...... On my Knuck there is a curve not to far from me if I go to fast through the curve I've had the back tire come off the ground..... Now that will get your attention fast.....

[Tattooo]

[ATTACH=CONFIG]90249[/ATTACH]

Yea it's a disc...... When he had the bike in the pic it looks like it had a drum on it..... I bet that's why they changed the wheel....

That's a nice frame.... It has had a good bit cut off of it already..... If you don't want a mech brake setup sure cut the cross over off..... Be careful when your cutting it off as you can sell it.....