CHOP CULT HOME
Email Password
Search

Hybrid View

  1. #1

    Join Date
    Sep 2010
    Posts
    11,522

    Default Starter Dive Headache .!!! This Bike will drive me to drink .... More !!

    Here's what's going on ....

    Click image for larger version. 

Name:	Capture ASD.JPG 
Views:	8 
Size:	84.2 KB 
ID:	87281

    That all of the engagement the bendix is seeing on the clutch drum starter ring gear...

    The bike was built a few years back from after/market parts...
    5 in a 4 tranny, S&S 93 inch Cone Shovel, a nice bike to say the least about it...

    Click image for larger version. 

Name:	IMG_1738.jpg 
Views:	3 
Size:	300.5 KB 
ID:	87282

    When I pulled the outer primary cover off to replace the bendix, seen three washers on the jackshaft ...

    Click image for larger version. 

Name:	Capture ASD2.JPG 
Views:	7 
Size:	47.4 KB 
ID:	87283

    Well, will ya look at that fine job of MICKEY-MOUSE-ing ...!!!

    OK, now to lick somebodyelse's calf here...

    First try was to order a new starter shaft, thinking that the shaft that has been used was from the 65-69 era...
    Ordered a 70 to 84 shaft, it came in, pulled out the shaft that the bike had and, GREAT SCOT .. !!!
    It was the same as the new shaft....

    Alright, now I'm thinking it has to be something is up with the starter .. ???
    Thought perhaps the starter was for the belt final drive models, this bike has a chain final drive.
    Tried for over a week talking with four diff. Fellas at Spyke to ID the starter... Sent lots of photos..
    Wanted them to pull from their stock both starters (Belt & Chain) and get some dimensions....
    Seems that Spyke has no numbers on their starters, zip !!!

    They couldn't help being the factory is across town with no-way to talk to someone that is somewhat a Tech...
    OK .... Now WTF ... !!!

    Talked it over with a tech at Tech Cycle, we came to the conclusion that the starter was for the belt drive models.
    So, with a grain of salt I ordered one from them after getting a Go-ahead from the owner.

    Click image for larger version. 

Name:	IMG_1831.jpg 
Views:	4 
Size:	289.7 KB 
ID:	87284

    Kick-ass in a word ... ^^

    It came in today ...
    For a look see to see what the diff. would be on the jackshafts, a little forensic investigation went down...

    Found both to be the same ....

    Click image for larger version. 

Name:	IMG_1828.jpg 
Views:	4 
Size:	288.7 KB 
ID:	87285
    Last edited by Dragstews; 10-06-2018 at 9:43 AM.

  2. #2

    Join Date
    Sep 2010
    Posts
    11,522

    Default

    Click image for larger version. 

Name:	IMG_1829.jpg 
Views:	1 
Size:	290.2 KB 
ID:	87287


    That got me thinking that the inner primary must be at fault ....
    It's not in the best of shape due to the chain eating into it ...

    Click image for larger version. 

Name:	Capture ASD6.JPG 
Views:	4 
Size:	96.5 KB 
ID:	87286

    Tried to ID it, was made by CCI ... Put in a call to them and was told that it's been years since they made inner primary's for the four speed bikes...

    Well ..... Kiss my Grits ... !!!!

    Without having a world of parts in stock to do a comparison, I feel like I'm .....

    Last edited by Dragstews; 09-13-2018 at 6:10 PM.

  3. #3

    Join Date
    Aug 2009
    Posts
    2,885

    Default

    Dude, I see all kinds of mis-matched shovel era starter setups.
    Multiple thrust washers are no big deal.
    As long as shit lines up lol

    First, make sure the shaft is long enough to not fall out the reduction gear.
    Then look to the top hat spacer (in your first pic).
    We've had to cut the shoulder with certain aftermarket inner and outer primaries. (Remember Lifeline?)

    Note: the belt drive shafts are way longer and have different splines. That match the belt style reduction gear...

  4. #4

    Join Date
    Sep 2010
    Posts
    11,522

    Default



    Lifeline International is still around ....

    Inner Primary Cover FL Precision CNC machined to fit 4-speed FL 1970 thru early 1984 models.

    Quote Originally Posted by Sky View Post
    As long as shit lines up lol
    Click image for larger version. 

Name:	IMG_1782.jpg 
Views:	2 
Size:	293.4 KB 
ID:	87294

    There's the problem ...
    If I remove two of those washers the starter drive will have more tooth contact, but at a price of the starter shaft not having much foot in the gear reduction ...

    Sky, take a hard look at what's going on in the below photo ...

    Click image for larger version. 

Name:	Capture ASD61.jpg 
Views:	6 
Size:	156.5 KB 
ID:	87295

    See the chain sawing into the cover .... ???
    ______________________________________________

    Bar-maid ..... Gimme a Bin Laden, Please ..

    How do you make that ?? .. She asks ..

    I tell her with two Shots and a Splash of water ..!!!
    Last edited by Dragstews; 09-13-2018 at 7:09 PM.

  5. #5

    Join Date
    Aug 2009
    Posts
    2,885

    Default

    Would a top hat spacer that didn't allow the shaft through as far be the answer?

    Big trans sprockets, lose/worn chains and short shocks. Primary killers

    I've fit smaller trans and wheel sprockets to increase clearance and keep the same final drive ratio.

    You probably have seen those clip on nylon shoes?
    They cool but do reduce clearance when installed.

  6. #6

    Join Date
    Sep 2010
    Posts
    11,522

    Default

    Here's my thoughts:

    Now that the jackshaft and starter has been verified as being for the 70-84 chain drive models, the only other item in the make up of controlling where the bendix gear makes contact to the clutch drum starter ring gear is the inner primary...

    It has to be the wrong one... Got to be, it's holding the starter away from going in far enough for full tooth contact of the bendix to ring gear...

    Hmmmmmmm.....
    I got an idea ....

    Going to find a Cal-Products C-30B inner and see if that will be the cure...



    Cal-Products Aluminum Inner Primary Covers,
    Fits Big Twins 1970-1982 (rear chain drive models only)



    RE-C30B, is the strongest replacement for failed 1970-1982 OEM inner chain cases.

    This case has an oil drain plug, however all other oiling holes are only center drilled since it is now a popular belief that the OEM design of running your engine oil over your clutch plates and primary chain would cause needless damage. You will have to switch to wet /dry aftermarket clutch plates and follow aftermarket mfg. recommendation for a light oil. Plug the hoses which were leading to and from the chain case. The front 2 outside bolts which bolt to the engine are now too short, our cases are another .280 THICKER. We suggest you run a tap all the way to the bottom of these holes to get clean threads and use as long of a bolt as you can, then washers on the out side to take up the difference.

    IT IS VERY IMPORTANT TO LOOSEN THE 5 BOTTOM TRANSMISSION BOLTS BEFORE YOU INSTALL THE CHAIN CASE, AND TIGHTEN THESE LAST OF ALL!

    FAILURE TO DO THIS MAY LEAD TO DISTORTION OR DAMAGE TO YOUR ENGINE CASE.

    We have machined a rectangle to accept the silly and stupid steel oil deflector plate. The square hole will help provide for a better seal and allow you to have something to glue the plate to, rather than depend on those stupid pins.

    The 4 side transmission studs are o.k. even though our chain case is another. 175 thicker at the washer surface and .250 thicker around the bearing than OEM.

    The 4 - 5/16 dia. Engine mount holes and the 4 - 3/8 dia Transmount holes are drilled SMALLER than OEM. We left them small for strength. In the event you have trouble getting them all to line up, slot with a round file.

    The starter mount area on the back of the chaincase is threaded for 2 - 1/4" studs as used on all pre-1978. If your starter motor housing is later, then it is threaded on the front hole to receive a bolt instead of a stud from the chaincase. While it is kind of awkward to get the nut on that front stud, if you use a flex extension for your socket and grease the nut and washer together in the socket it's easier than wrestling with the gasket, steel oil deflector plate, the pins, and the starter motor. If you choose to use the studs you will need to drill out the threads on the starter housing. If you are a good juggler, then drill out our beautiful virgin chaincase....

    That "rough" finish on the inside and outside is shot peening which distresses the surface to prevent cracks. This surface is created in a special machine which "throws" hardened steel BB's at a high rate of speed into the surface of the casing. No air is used in our shot peening operations

    You have by now noticed our chain housing is much heavier throughout than any other. This extra metal will help your primary run quieter by dampening the sound and maintaining alignments.
    Last edited by Dragstews; 09-14-2018 at 12:44 PM.

Share This



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Log in

Log in