Show off those custom mid controls!

**TheSandman** · 07-15-2012

I know JJ has a thread, but we should have one over here. I'm not talking about stock mids on a stock bike. I'm talking custom shit!

Here's a pic of one setup that I like. I'm trying to figure out the right side. I have normal drags so they're low and somewhat close to the frame.

**Revelator** · 07-15-2012

Here is my Clutch setup that I made. Also made the Pegs & the stainless Peg pivots.

**TheSandman** · 07-15-2012

Quote:

Originally Posted by Revelator

Here is my Clutch setup that I made. Also made the Pegs & the stainless Peg pivots.

What's your right side look like?

**TheSandman** · 07-18-2012

Well this thread didn't take off.

**LDNCLR** · 07-18-2012

I made these from some stainless plate, but I pretty much hate them already and will be changing them soon.

**EnglandStGarage** · 07-18-2012

I did a fab kevin rear disc brake/caliper set up on my right side shift ironhead. It was pretty easy to do the hydraulic setup when i had forward controls cause i just made an mc mount and welded it to the frame. When I redid my bike I really wanted mid controls. I had to make these from scratch. they don't look professionally made by any means but they were cheap as hell to make and they work well!

**TheSandman** · 07-18-2012

Quote:

Originally Posted by LDNCLR

I made these from some stainless plate, but I pretty much hate them already and will be changing them soon.

That's kind of want I wanna do. I don't think that looks bad at all. If I had to pick at it, the shifter arm could be prettier, but none the less, it looks good!

What mount did you use on the frame for your pegs?

Any pics of the right side?

**misfitJason** · 07-18-2012

Hahaha. Yeah the thread on jj is mine. Now I am contributing to this one too. To bad I can't figure out how to post pics from an iPad

**2siq600** · 07-18-2012

heres mine... work in progress.

**GRHebard** · 07-18-2012

heres mine that i made on my XS

07-19-2012

Quote:

Originally Posted by TheSandman

I know JJ has a thread, but we should have one over here. I'm not talking about stock mids on a stock bike. I'm talking custom shit!

Here's a pic of one setup that I like. I'm trying to figure out the right side. I have normal drags so they're low and somewhat close to the frame.

That looks like a re-purposed Evo sporty mid control mount. I've been thinking of using the later, rubber-mount passenger peg mounts from a sporty as mids. They are pretty nice cast pieces with a flat mounting surface. You might look at one of those for your right side solution.

**TheSandman** · 07-19-2012

Quote:

Originally Posted by billdozer

That looks like a re-purposed Evo sporty mid control mount. I've been thinking of using the later, rubber-mount passenger peg mounts from a sporty as mids. They are pretty nice cast pieces with a flat mounting surface. You might look at one of those for your right side solution.

Yeah I was thinking they look similar to a sporty setup. I would like to see more pics of the mid controls mount that bolt to the floorboard tabs on a shovel frame.

Doesn't a CC member make those?

**elTee** · 07-19-2012

4" up.. if I scrape now, most likely I'm laying it down...

**2siq600** · 07-20-2012

^^^^^^ wish i had just made some clean simple ones like that mine are turning into a huge cluster fuck!

**LDNCLR** · 07-20-2012

Quote:

Originally Posted by billdozer

That looks like a re-purposed Evo sporty mid control mount. I've been thinking of using the later, rubber-mount passenger peg mounts from a sporty as mids. They are pretty nice cast pieces with a flat mounting surface. You might look at one of those for your right side solution.

they are evo generation Dyna peg mounts. Cory Hebert at Maindrive sells a beautiful set up, but I couldn't justify the price.