CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: farmall

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.07 seconds; generated 57 minute(s) ago.

  1. http://www.backroadbbqrun.com/ has nothing...

    http://www.backroadbbqrun.com/ has nothing saying otherwise.
  2. Replies
    11
    Views
    272

    The 9-spoke mag solves your speedo drive...

    The 9-spoke mag solves your speedo drive problem.. Attached pic shows da notch and what ya need to do on any other wheel. (A round-bottom notch is fine, I just ground one on a rotor I forgot to order...
  3. Post how the run works out. I can't do it...

    Post how the run works out.

    I can't do it this year (awaiting back surgery) but maybe next year.
  4. Replies
    12
    Views
    287

    Pics show why the repop witch hat bearing sucks....

    Pics show why the repop witch hat bearing sucks. The race looks like it was machined with a railroad spike:

    https://www.jockeyjournal.com/forum/showthread.php?t=102773

    Too bad the Shovelhead...
  5. Replies
    12
    Views
    287

    How do you set up yours and what plates and...

    How do you set up yours and what plates and springs do you prefer? Three or five stud hubs?
  6. Thread: Throttle cable

    by farmall
    Replies
    10
    Views
    223

    I use screw-on cable ends as well and also for...

    I use screw-on cable ends as well and also for the ability to use any cable and to use (and I have) bicycle shifter cables as emergency throttle cables on the road.

    The spark plug nut method is...
  7. Replies
    13
    Views
    330

    Drag Specialties has good photos of it. The...

    Drag Specialties has good photos of it. The V-Twin pics of what's highly likely to be the same casting aren't as good. Hard to tell cross section thickness without measuring though.
  8. Replies
    11
    Views
    278

    If you want more torque for Dremel bits the...

    If you want more torque for Dremel bits the RotoZip tools have a selection of collets including 1/8". I bought one without a base at a yard sale and often use it instead of a Dremel as it's got much...
  9. Replies
    12
    Views
    287

    Taper joints get keys to augment the holding...

    Taper joints get keys to augment the holding power and work as a combo (the other use of keys is timing, irrelevant for a clutch). The higher quality key the better.

    Loctite is specifically...
  10. Replies
    11
    Views
    278

    Thanks for the dimension info. Many sellers omit...

    Thanks for the dimension info. Many sellers omit that. That style package means I can snip the tab and use an aircraft cushion clamp (round but easy to bend square) to hide it if I don't care for the...
  11. Replies
    10
    Views
    628

    You can make a simplified wiring harness pretty...

    You can make a simplified wiring harness pretty compact and check out vintage auto suppliers for sexy wire coverings. You can also make your harness as clean as practical by ensuring your wires are...
  12. Replies
    12
    Views
    287

    Since plenty of those kits have succeeded over...

    Since plenty of those kits have succeeded over many years, I'd wonder what caused the locking compound not to work. Were all threaded surfaces cleaned with a non-oily solvent prior to application?...
  13. Replies
    13
    Views
    330

    V-Twin do but the Delkrons are beasts. Is the...

    V-Twin do but the Delkrons are beasts. Is the other one (if not V-Twin) just a stock replacement?

    FXRs like to crack stock inner primary covers. I'm still waiting on Solenberg (Delkron) to...
  14. Replies
    8
    Views
    164

    All of them in a circle chowing down on each...

    All of them in a circle chowing down on each other would be of great technical merit.
  15. Replies
    11
    Views
    278

    Interesting thread! There are many collectible...

    Interesting thread! There are many collectible and high dollar Shovels which could benefit.

    I'm searching that Rotek starter relay as it's close to the little Bosch units in form factor but much...
  16. Replies
    8
    Views
    164

    JBinNC and Dragstews: Since you gents build...

    JBinNC and Dragstews:

    Since you gents build more Shovels than anyone else here by a long shot, and OP bought a basket so we have a (potentially) good thread for this if OP posts pics, what would...
  17. Replies
    13
    Views
    330

    Better yet get rid of the transmission and...

    Better yet get rid of the transmission and upgrade to a splined shaft unit.

    BTW Solenberg aren't doing the Delkron inner FXR primaries but they did make a run of trans cases and they're NICE. I...
  18. Replies
    8
    Views
    164

    ^^^ What he said ^^^ I've always had to nudge...

    ^^^ What he said ^^^

    I've always had to nudge the shaft a cunt hair from the timing cover side. While you're there you'll have the pushrods off to unload the cam so inspect your cam lobes and...
  19. Replies
    4,276
    Views
    303,673

    Have some Rory Gallagher: ...

    Have some Rory Gallagher:

    https://www.youtube.com/watch?v=go9J9REtfdA&feature=youtu.be
  20. Replies
    4
    Views
    169

    Review your wiring methods and practices to...

    Review your wiring methods and practices to ensure a professional job. If you even think of using those shitty sleeved auto store splices, do not.
  21. Replies
    13
    Views
    330

    Speaking of fingers, is either of those or...

    Speaking of fingers, is either of those or anything else an upgrade over the similar early five speed release fingers that I've seen break?

    37084-79 is the part number in my early FXR book. I...
  22. Replies
    19
    Views
    573

    You might want to add some holes to that...

    You might want to add some holes to that engine-strangler air cleaner cover, If you have a milling machine they could be sexy slots.

    I love the chuck on the brake lathe. If you can score a cross...
  23. Congrats on escaping the metro area (I knew it...

    Congrats on escaping the metro area (I knew it would turn to shit and left NJ in '81)!

    Check on the Weldingweb and Miller welding forums for fellow fabricators. I'm not a pro and live in SC so...
  24. Replies
    6
    Views
    240

    Have it machined from something stronger next...

    Have it machined from something stronger next time. If you can find out what they used on the failed axle post that for reference.

    Your shop can advise on alloy and may have some stock left over...
  25. Nice score.

    Nice score.
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4

Log in

Log in