CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: WALLY77

Page 1 of 5 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    9
    Views
    617

    I read that article last night while searching...

    I read that article last night while searching for answers. Thanks for the heads up
  2. Replies
    9
    Views
    617

    Hey no problem. Threads without pics are useless.

    Hey no problem. Threads without pics are useless.
  3. Replies
    9
    Views
    617

    Hard to get a good picture, I'll pull the forks...

    Hard to get a good picture, I'll pull the forks out just to be sure. Now in the manual it said to "time" the shift forks to the lid before putting it back on, also said a special tool is needed to...
  4. Replies
    9
    Views
    617

    ratchet top hard down shift

    OK Ill start off with a little info, bike is a 77 shovel with a matching 77 ratchet top trans in a rigid frame. Bdl inch and a half open belt primary, foot clutch hand shift.

    I have a factory...
  5. Replies
    8
    Views
    710

    I just went through this with my BDL setup after...

    I just went through this with my BDL setup after I snapped a belt due to worn out pulleys and or running it way too tight. Now, according to them to set the tension you install the stock inner...
  6. Biltwell rules!

    Biltwell rules!
  7. Replies
    114
    Views
    14,380

    BDL finally got back to me about proper belt...

    BDL finally got back to me about proper belt tension so Ill post it here for those of us that dont have the inner primary to set the tension with.

    with the engine cold they recommend 1/2 to 5/8...
  8. Replies
    114
    Views
    14,380

    Thanks guys, it sure has been a blast ripping...

    Thanks guys, it sure has been a blast ripping around on this thing thats for sure.

    I got the new belt and pulleys on, installed a clutch tamer (think thats what its called) and cleaned/serviced...
  9. Replies
    114
    Views
    14,380

    Was ripping down a road in the middle of nowhere...

    Was ripping down a road in the middle of nowhere eastern Washington saturday and felt something hit my leg right about the same time the rpms
    spiked... fuck there goes the belt

    ...
  10. Replies
    114
    Views
    14,380

    Modified some swap meet pipes i had laying around...

    Modified some swap meet pipes i had laying around and bolted them on. way better looking than the other ones and they are loud as fuck :cool:

    https://i.imgur.com/Lu6LPYpl.jpg...
  11. Replies
    114
    Views
    14,380

    So got my master cylinder rebuilt and sealed up,...

    So got my master cylinder rebuilt and sealed up, only after it spewed all over the frame and fucked the paint... ohwell.
    Tranny leak turned out to be the seal in the end of the fourth gear,...
  12. Replies
    114
    Views
    14,380

    Thanks fellas. Got it out today for a short rip,...

    Thanks fellas. Got it out today for a short rip, runs good and pulls hard but the tranny is PUKING from in behind the sprocket and my brand new made in china master cylinder is leaking like a bastard...
  13. Replies
    3
    Views
    1,345

    Man this post couldn't have come up at a better...

    Man this post couldn't have come up at a better time Haha, just got my bike back together and took it for a rip today and the tranny is PUKING from behind the sprocket

    I did seal up the studs...
  14. Replies
    114
    Views
    14,380

    Hey thanks. I'm going to throw a plate on it...

    Hey thanks. I'm going to throw a plate on it tomorrow and put on a few miles, I'll grab some better pics then
  15. Replies
    114
    Views
    14,380

    got my hands on a complete mid star 21 inch wheel...

    got my hands on a complete mid star 21 inch wheel so i ditched the hideous twisted spoke 19 inch front and chucked on a speedmaster instead. And thats how it sits while I wait for a $3 brake line...
  16. Replies
    114
    Views
    14,380

    re assembly went quick so didnt take many pics....

    re assembly went quick so didnt take many pics. with everything back on there was too much black so i layed down some shitty 30mph flames to break it up a bit. Fuck me is masking off flames for paint...
  17. Replies
    114
    Views
    14,380

    Got everything painted now so time to start re...

    Got everything painted now so time to start re assembling. Had to get up early around 5am to get all my painting done before the heat and wind picked up, turned out decent enough for me. not a show...
  18. With an elevation change like that it's running a...

    With an elevation change like that it's running a bit rich for sure. I bought a bike a few years back and brought it from sea level up to 3000ft and had to move down a size on the pilot and main jets...
  19. Replies
    114
    Views
    14,380

    Got everything blown apart over the weekend and...

    Got everything blown apart over the weekend and finished all the welding on the frame that I couldnt reach. Going to build a make shift paint booth in my shop and try my hand at painting. Picked up a...
  20. Replies
    114
    Views
    14,380

    I have used that stuff in the past on various...

    I have used that stuff in the past on various projects. Works well
  21. Replies
    6
    Views
    1,066

    Are you going kick only or electric start? If its...

    Are you going kick only or electric start? If its kick only then no need for any relays. Fuses do the same thing as circuit breakers except they are one time use but Im sure you know that already. As...
  22. Replies
    114
    Views
    14,380

    found a caliper that i believe is off an evo...

    found a caliper that i believe is off an evo softail at a local swap meet. fits right in between the frame rails, just needed to cut down the adjuster bolt to clear and weld a tab onto the frame for...
  23. Replies
    114
    Views
    14,380

    After kicking it over and not getting any...

    After kicking it over and not getting any reaction at all is when I found out that the little "kill" switch I have is actually a momentary on switch and not a momentary off. Ran a temp jumper wire to...
  24. Replies
    114
    Views
    14,380

    was cold as fuck here for a couple weeks and my...

    was cold as fuck here for a couple weeks and my shop dont have heat so nothing much got done.
    Got the wiring and battery box wrapped up

    https://i.imgur.com/g4MrR4Gl.jpg...
  25. Love it, nice work man

    Love it, nice work man
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4

Log in

Log in