CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Sky

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.03 seconds.

  1. Replies
    5
    Views
    131

    Drilling off the bolt heads is another option

    Drilling off the bolt heads is another option
  2. Thread: dyna ignition

    by Sky
    Replies
    3
    Views
    143

    Are we talking the Dyna-S or the 2000-i ?...

    Are we talking the Dyna-S or the 2000-i ?
    Single or dual fire?

    What do you want to know? What does the guy who installed it say?
  3. Replies
    3
    Views
    134

    You're using the wrong keywords in your searches...

    You're using the wrong keywords in your searches
    Ditch "Fatboy"
    Try "Softail" and "forward controls"
  4. Replies
    3
    Views
    131

    Nobody's happy with those levers for long, They...

    Nobody's happy with those levers for long,
    They simply don't stand up to regular use.
    Just do the feeler gauge trick
  5. chopper forensics! Here's a short list off the...

    chopper forensics!
    Here's a short list off the top of my head

    Lack of lubrication
    Check tappet screen first
    Blocked oil passages
    Synthetic oil (tendency for some bearings to "skate")
    Did you...
  6. Replies
    3
    Views
    170

    Are you trying to compare rubber mount to solid...

    Are you trying to compare rubber mount to solid mount frames?
  7. Replies
    5
    Views
    207

    80 ft lbs and red locktight Ditch the tab washer...

    80 ft lbs and red locktight
    Ditch the tab washer to gain thread engagement
    If sprocket has a threaded hole, install "safety" screw
  8. Replies
    10
    Views
    250

    The above is all very good advice. This is a...

    The above is all very good advice.

    This is a fresh build, right?
    So you are sure the cam bushing and inner cam bearing are good?
  9. Replies
    4
    Views
    238

    Only way to be sure... Make them yourself. Diy...

    Only way to be sure...
    Make them yourself.
    Diy kits with flanges are available, but I just cut up used pipes.
  10. Replies
    42
    Views
    998

    Adjust pushrods and check compression again. If...

    Adjust pushrods and check compression again.
    If comp comes up, good. Try to start her...
    If not pull pushrods and do a "redneck leakdown"

    If it's a fresh motor, might wanna re-torque the heads...
  11. That needle is real fat in the mid-range, As it...

    That needle is real fat in the mid-range,
    As it was meant for a non-accelerator pump carb.
    I doubt you'll need it with with that cam
  12. Tiny air cleaners with paper elements are a...

    Tiny air cleaners with paper elements are a choking point.
    Restrictive baffles are, well, restrictive.
    There is more to tuning a CV carb than jetting. It is a CV, right?
  13. Looks like a wide glide hub Your gonna need a...

    Looks like a wide glide hub
    Your gonna need a new wheel to go narrow

    Are those 41mm tubes? And lowers?
    If so you'll need aftermarket trees and axle
    Or machine your own, plus axle
  14. Replies
    10
    Views
    375

    I believe the Mullins trees were available in 39...

    I believe the Mullins trees were available in 39 and 41 mm. Which ones do you have?

    If the eBay seller listed 41mm lowers as 39mm, his mistake.

    The rib at the top is for a rubber dust boot.
  15. Thread: Carb Dilema

    by Sky
    Replies
    25
    Views
    1,022

    California prices must be outrageous 250 for a...

    California prices must be outrageous
    250 for a carb "housing"?!
    Only way I know of to buy a carb body is used.
    Go to a swap, buy a used CV. Don't pay more than $100

    Pro tip:bring a couple of...
  16. Replies
    12
    Views
    652

    Stop overtighting them. Feel, Daniel San, feel....

    Stop overtighting them.
    Feel, Daniel San, feel.
    I remove and replace those all the time,
    Only ever broke one... Or two
    All it needs is a snug to keep it in place, little more than finger tight....
  17. Replies
    7
    Views
    870

    Yup measure the od and Id, then to head to your...

    Yup measure the od and Id, then to head to your local bearing house.
  18. Your Speedo is "married" to the ECM via the VIN...

    Your Speedo is "married" to the ECM via the VIN number.
    You'd need the Harley dealer interface module to change it or replace it.

    Why not french it into that sporty tank?
    Lots of in your face...
  19. Replies
    32
    Views
    1,374

    Main breaker wouldn't show a deterioration of...

    Main breaker wouldn't show a deterioration of performance.
    Just a sudden lack of spark (and lights) till it resets.
    But I have seen corrroded/damaged breakers. loose posts, lose bolts, bad...
  20. Thread: Titan front forks

    by Sky
    Replies
    6
    Views
    599

    Hey that's the nickname my ex gave me! Great Big...

    Hey that's the nickname my ex gave me!
    Great Big Cock..
    Do you know what that company's abbreviation stands for?

    Also what year make and model of titan are we talking?
    Post a pic showing us...
  21. Replies
    32
    Views
    1,374

    A lot of good advice in this thread so far......

    A lot of good advice in this thread so far...
    Are you certain your issue is heat related? Vibration is synonymous with Shovelheads

    Double checking or even adding good ground(s) has not been...
  22. Replies
    3
    Views
    694

    Accelerator pump adjustment

    We are talking of course about fine tuning the volume and timing of the pump squirt intended to cover the lack of fuel during a "braaaap" moment.

    This adjustment has been covered
    Instruction...
  23. Replies
    8
    Views
    488

    Wire springs or a diaphragm? Or what? There is a...

    Wire springs or a diaphragm? Or what?
    There is a correct way to set up the spring(s) too

    A wobbly clutch hub bearing can be troublesome as well

    If the clutch lever had enough travel before the...
  24. Replies
    5
    Views
    507

    Anytime you increase trail you also increase...

    Anytime you increase trail you also increase high-speed stability. Longer tubes with no other changes increases trail. So you will be less likely to get that wobble.
    However low speed manuvers may...
  25. Replies
    31
    Views
    1,291

    Every one of us should take this advice to heart...

    Every one of us should take this advice to heart

    And ASAP = which equaled two months for me.
    Woman driving the wrong way down a one way.
    It hurt and my GF left that night. Slashed my ex's...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in