CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ncmc47

Page 1 of 5 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    6
    Views
    353

    When he tops a bridge, he's in for the wheelie of...

    When he tops a bridge, he's in for the wheelie of his life!
  2. Replies
    8
    Views
    211

    In m y limited experience the S&S shat was longer...

    In m y limited experience the S&S shat was longer than my stock shaft(knuckle)
  3. Replies
    12
    Views
    373

    Is there more than one length?

    Is there more than one length?
  4. Replies
    23
    Views
    833

    Unless you put a seat for her, her ass will go...

    Unless you put a seat for her, her ass will go numb anyway! LOL
  5. Replies
    18
    Views
    545

    I don't know what BDL spec's are but that seems...

    I don't know what BDL spec's are but that seems like a lot of slack to me.
  6. Replies
    13
    Views
    478

    This appears wider than stock across the axle...

    This appears wider than stock across the axle plates, perhaps for a wide tire and belt drive. That maybe a plus if that's what you're looking for. Looks to me like a VTwin frame!
  7. Replies
    164
    Views
    7,363

    Thanks

    Thanks
  8. Replies
    164
    Views
    7,363

    Does anybody have contact info on Jeff Grossman...

    Does anybody have contact info on Jeff Grossman of Bull Dog Cycles? A quick search showed the heat cycles of bull dogs LOL! There were several on Face Book, but didn't find the right one, I guess.
  9. Replies
    12
    Views
    256

    Looks like it should work, do you have a ball...

    Looks like it should work, do you have a ball valve on the drain on your tank? Depending on the compressor you may need an elbow and and a 4 or 6 " piece of pipe to get the ball valve out where...
  10. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    Pleas let us know what the problem was.

    Pleas let us know what the problem was.
  11. Replies
    43
    Views
    835

    The anchor rod should go to the solid leg of the...

    The anchor rod should go to the solid leg of the springer and level is much better.
  12. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    Come on, inquiring minds need to know!

    Come on, inquiring minds need to know!
  13. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    Don Schaffer of S&S recommended to me, a few...

    Don Schaffer of S&S recommended to me, a few years ago, that knuckles run best about 31 degrees BTDC, which puts the timing mark about half way through the hole or close to center with my degree...
  14. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    Also I would take Jesse's comment on fuel...

    Also I would take Jesse's comment on fuel literally! Make sure you have good clean fuel in your tank or make a substitute tank out of a small container and make sure gas is fresh and no water in it....
  15. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    Instead of sticking your thumb over the plug...

    Instead of sticking your thumb over the plug hole, pop your pushrod covers on the front cylinder and rotate until they are both bottomed. (lifters) Only then will you be sure you're on compression...
  16. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    It's totally crap, send to me, I'll junk it out! ...

    It's totally crap, send to me, I'll junk it out! LOL Are you sure your timing isn't 180 out?
  17. Thread: 41 el

    by ncmc47
    Replies
    635
    Views
    16,778

    The lessons I remember best are the ones I...

    The lessons I remember best are the ones I learned the hard way!
  18. Thread: Frame jig plans

    by ncmc47
    Replies
    8
    Views
    1,181

    Gary I'm glad to see your website up and running...

    Gary I'm glad to see your website up and running again. You have been missed. I'm sure a new generation of builders will find their way to your site. You have so much good to offer.
  19. Replies
    20
    Views
    2,189

    Prolly 49 or up!

    Prolly 49 or up!
  20. Replies
    50
    Views
    2,532

    I would run an Overbearing setup from I think...

    I would run an Overbearing setup from I think it's bare Knuckle choppers with those main drive bearings. $110 shipped when I bought mine.
  21. Replies
    453
    Views
    18,340

    I have a 30 degree non bullneck frame that is...

    I have a 30 degree non bullneck frame that is pretty stock that has no clearance on the back exhaust valve cover. It probably came frome the factory that way because it has wear marks in the seat...
  22. Replies
    1
    Views
    274

    There's an internet company that will run a check...

    There's an internet company that will run a check for you, if you know the serial number. It costs $25. I think it's called vin check.
  23. Replies
    18
    Views
    1,088

    37 degree flares should use a sleeve between the...

    37 degree flares should use a sleeve between the flare and the nut to prevent breakage and aren't double flared. You can get the nuts and sleeves through Speedway or aircraft houses.
  24. Replies
    13
    Views
    630

    Aircraft have two mags to combat detonation,...

    Aircraft have two mags to combat detonation, which would blow a head or cylinder apart quickly. the fact that it has some redudency is a slight convience. Aircraft cylinders are rarely bored out,...
  25. Replies
    32
    Views
    1,678

    Could be a condenser getting ready to let go. ...

    Could be a condenser getting ready to let go. Just because they're new doesn't mean they're good, they can break down on the shelf.
Results 1 to 25 of 109
Page 1 of 5 1 2 3 4

Log in

Log in