CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ironhead86

Page 1 of 11 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    6
    Views
    704

    I belive PBI makes a 3/4 offset sprocket

    I belive PBI makes a 3/4 offset sprocket
  2. Something else to factor in on timing is what...

    Something else to factor in on timing is what your building. Drag/street bike, low compression mild mile muncher, dual plugs cams. A BIG FACTOR are you using voes or cutting it out. Some require it...
  3. Can you get oil circulating, sounds like a...

    Can you get oil circulating, sounds like a weakest link deal. If their is a clog then the oil has no where to go. Also glassing surfaces like that do help, but you can take to much off causing other...
  4. I can give you some blunt advice. You took your...

    I can give you some blunt advice. You took your bike to a shop, because you do not feel your welding is up to par. Thats fine we all start somewhere. Your paying this shop to do frame or mechanical...
  5. Replies
    5
    Views
    619

    75 is good but other locals pay better. Iw local...

    75 is good but other locals pay better. Iw local 86
  6. Replies
    1
    Views
    360

    Dont put a bolt in, get the rubber stopper. Like...

    Dont put a bolt in, get the rubber stopper. Like on a old sink or tub. That way its sealed and dont need to worry about mashing your ring gear if the bearing goes out.
  7. Replies
    28
    Views
    1,822

    Thats fucking awsome fuck those pigs

    Thats fucking awsome fuck those pigs
  8. Replies
    22
    Views
    1,627

    Why not just ride a stock bike. Oh cause some...

    Why not just ride a stock bike. Oh cause some people dont want to.
  9. Me and linkbelt are in the same profession, he is...

    Me and linkbelt are in the same profession, he is a stand up guy and has more experience then I have been alive. Redwings last 6mo till the soles are gone and beyond repair. The 877s are still made...
  10. Replies
    10
    Views
    6,113

    Are you running voes

    Are you running voes
  11. Replies
    6
    Views
    950

    Check classifieds guy just threw some on. If you...

    Check classifieds guy just threw some on. If you were closer*
  12. Replies
    7
    Views
    819

    I would say that its a possibility, cause...

    I would say that its a possibility, cause anything is. Is it worth the time and money thats your call.

    Or send yours off to forking by frank do it the cleanest most painless way. And unlike...
  13. Replies
    7
    Views
    819

    http://i1090.photobucket.com/albums/i379/ccmillers...

    http://i1090.photobucket.com/albums/i379/ccmillersea/Posted%20photos/16613003683_06d7078e98_o_zpsshsrhhxr.jpg
  14. Replies
    382
    Views
    8,995

    Yes Please

    Yes Please
  15. Replies
    10
    Views
    6,113

    Tune the low speed jet with the accelerator pump...

    Tune the low speed jet with the accelerator pump completely OFF/DISENGAGED. If you dont it will cause issues, like improper jetting. most people set the pump 2 turns then try to tune it, all it does...
  16. Replies
    7
    Views
    653

    I would run em but instead of lifting the front...

    I would run em but instead of lifting the front mount. I would make it thinner in the front keeping the taper to the rear. So you can show off the pans a little more, and not have the top heavy look.
  17. Thread: Union work?

    by ironhead86
    Replies
    98
    Views
    5,380

    I am a union ironworker. Do alot of connecting...

    I am a union ironworker. Do alot of connecting and structural. It gives me a boner being 30ft+ in the air, telling a crane operator what to do. Or having 6 thousand lbs 3ft overhead while hooking on...
  18. Replies
    9
    Views
    561

    Mate, deck, line bore, and shim m.m and your...

    Mate, deck, line bore, and shim m.m and your done. unless you want to deck m,m surfaces. 400 bucks is big $ to some not to me for a bike. As far as belly numbers go. That a vin subject to me.
  19. Replies
    17
    Views
    978

    I vote and will put in action, a evo motor, hop...

    I vote and will put in action, a evo motor, hop it up and not be bummed when its fried from hard RIDING instead of 2 the cost to keep my vintage cool.
  20. Thread: Western WA

    by ironhead86
    Replies
    85
    Views
    5,702

    Thats a clean scooter

    Thats a clean scooter
  21. Thread: Western WA

    by ironhead86
    Replies
    85
    Views
    5,702

    62724 A idea... throw up a pick of what you...

    62724

    A idea... throw up a pick of what you ride 99% of the time. So I know what your on when im out and about
  22. Replies
    26
    Views
    27,824

    Barnett steels and fibers and atf. Never had a...

    Barnett steels and fibers and atf. Never had a clutch walk since the change 3 years ago
  23. Replies
    1
    Views
    268

    Vancouver wa. By portland?

    Vancouver wa. By portland?
  24. Thread: Western WA

    by ironhead86
    Replies
    85
    Views
    5,702

    Jjj123 Ya I will be there with a few others. Not...

    Jjj123 Ya I will be there with a few others. Not sure what bike. Either a chopped ironhead or evo sporty with no mirrors.

    Weepster1, I am working in Everett. And would be down to go ride one of...
  25. Replies
    26
    Views
    2,162

    And dont forget the conformation email. Fuck...

    And dont forget the conformation email. Fuck traffic
Results 1 to 25 of 269
Page 1 of 11 1 2 3 4

Log in

Log in