CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Pliers

Page 1 of 5 1 2 3 4

Search Forums: Search took 0.09 seconds.

  1. Replies
    18
    Views
    723

    So I checked all of my wiring and found no...

    So I checked all of my wiring and found no obvious issues. Pulled carb yet again, stripped completely and soaked, new gaskets, etc...Started on 2nd kick after 2 prime, let it run for a min, seems ok...
  2. Replies
    18
    Views
    723

    Somthing's still amiss....I'll keep digging

    Somthing's still amiss....I'll keep digging
  3. Replies
    18
    Views
    723

    Thanks, good suggestions. Im gonna try to...

    Thanks, good suggestions. Im gonna try to isolate all parts of the electrical system and go over fuel system again, as well. I'm sure it will be something simple....
  4. Replies
    18
    Views
    723

    All good, thanks. I got load test done, and...

    All good, thanks. I got load test done, and ended up buying my own load tester as well so I'll have one in the future without having to rig something up. So, battery was shot. Battery was new when...
  5. Replies
    18
    Views
    723

    Tattooo, yes, I know i need to do a load test. ...

    Tattooo, yes, I know i need to do a load test. Planning on it today, will report back....
  6. Replies
    18
    Views
    723

    Last I checked, the battery (2 days ago) was...

    Last I checked, the battery (2 days ago) was reading 12.6, but, I did not recheck yesterday when I was fucking with ignition etc...I will check again this morning, would be nice if that's all it...
  7. Replies
    18
    Views
    723

    Yes, I agree that something went amiss...

    Yes, I agree that something went amiss during/after initial ride. Plugs are black/gas fouled. I pulled carb again (downdraft manifold) looked for debris. I feel like it is carb related but I...
  8. Replies
    18
    Views
    723

    getting 77 shovel on the road

    Looking for some fresh ideas to help work out the bugs on this scooter.

    Bike: 77 fxe, A grind cam, drag pipes (i know...), SU eliminator II, points ignition, 2" open belt, pro clutch

    First ride...
  9. Replies
    6
    Views
    469

    3/4 conduit is 1 1/8 O.D. I use rigid stainless....

    3/4 conduit is 1 1/8 O.D. I use rigid stainless. There are some who may advise against it but I have used it successfully....of course I have easy access because I work with it everyday, just a...
  10. Mike at 47 did a frame for me last year. He was,...

    Mike at 47 did a frame for me last year. He was, quick, professional, easy to work with. Frame turned out nice. Just my .02....
  11. Check with Jim in highpoint. He's helped me out...

    Check with Jim in highpoint. He's helped me out a good bit
  12. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99617

    99617
  13. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99616

    99616
  14. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    I found an old bearing puller collet, im going to...

    I found an old bearing puller collet, im going to make a homemade Jims tool from it....
  15. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    Got it apart, got the jims bushing tool on the...

    Got it apart, got the jims bushing tool on the way, with a bushing reamer. Im supposing i should probably replace the cover bushing as well while im at it....if so i believe i'll need a special...
  16. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99573

    99573
  17. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99572

    99572
  18. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99571

    99571
  19. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    Yes, the dowel pin was in the bushing, so it...

    Yes, the dowel pin was in the bushing, so it wouldnt spin but was a loose fit. I pulled it out with a small amount of force, but by hand. I have been looking at the line ream operation online, Ive...
  20. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    I dont think the bushing was spinning in the...

    I dont think the bushing was spinning in the case, but when i went to pull cam to i.d. it the bushing just pulled out with it. I dont know a whole lot of the history of the motor, it was an...
  21. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99532

    99532
  22. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99531

    99531
  23. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    Using phone for pictures, not working out....

    Using phone for pictures, not working out....
  24. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99530

    99530
  25. Thread: 53fl rebuild

    by Pliers
    Replies
    26
    Views
    1,156

    99528

    99528
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4

Log in

Log in