CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: DustyDave

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    62
    Views
    1,380

    Lapping on a surface plate, piece of granite or...

    Lapping on a surface plate, piece of granite or even a thick piece of glass with a sheet of wet or dry sandpaper stuck on top is usually successful I even used a tennis court directly on the concrete...
  2. Replies
    9
    Views
    312

    I was dam near run over by a woman driving a mini...

    I was dam near run over by a woman driving a mini van in 2 lanes holding her cell up by the roof so she could see to text in the sun she was driving into with a quart of Old English 800 in the other...
  3. Replies
    27
    Views
    1,482

    Put a bolt and nut through the spacer n chuck it...

    Put a bolt and nut through the spacer n chuck it up in a drill. While its spinning start the cut with the corner of a file, when the grove is where you want it saw it off with a hacksaw. If you...
  4. Replies
    3
    Views
    241

    A small caliper for the hand lever and leave the...

    A small caliper for the hand lever and leave the foot brake alone is a common solution. I like using the Indian Four clutch pedal that latches down. Mountain roads and lots of drunken neighbors make...
  5. Replies
    5
    Views
    176

    Merry Merry Happy Happy Ho Ho n all that shit!...

    Merry Merry Happy Happy Ho Ho n all that shit!
    Dusty
  6. Replies
    19
    Views
    405

    Doesn't matter about the font the boss has been...

    Doesn't matter about the font the boss has been filed down. Don't ride that one anywhere it might be subject to inspection.
    Dusty
  7. Replies
    22
    Views
    602

    I always assumed that the output or power...

    I always assumed that the output or power transistor was going dead short cyclically. But was never interested enough to de-pot and test since a new regulator was always a cure.
    Dusty
  8. Replies
    22
    Views
    602

    The internal regulator that goes in a Toyota...

    The internal regulator that goes in a Toyota forklift alternator or more recently the mini Denso hotrod alternator. Any time I see one cycling like he described after warmup its gonna die soon. Most...
  9. Replies
    22
    Views
    602

    That cyclic fluctuation is the first stage of...

    That cyclic fluctuation is the first stage of regulator failure on the Nippon Denso regulators I use. As the manuals always say substitute a known good part and observe.
    Dusty
  10. Replies
    8
    Views
    775

    A friend built this one bout 8 years ago for one...

    A friend built this one bout 8 years ago for one of his handicapped friends, he couldn't pick up his feet more than a coupla inches, hence the step thru design. VW engine with auto trans, Kawa 600...
  11. Replies
    277
    Views
    12,426

    Isn't it amazing that the vaccine was great and...

    Isn't it amazing that the vaccine was great and gonna save us all when Trump had it developed. And then a Democrat is elected and it's a government conspiracy. Hard to fathom how the facts change...
  12. Replies
    277
    Views
    12,426

    107110

    107110
  13. Replies
    2
    Views
    374

    The other way over the top metal work build was a...

    The other way over the top metal work build was a Knuck http://www.chopcult.com/forum/showthread.php?t=48039 It was more stainless than Selectedgrub but worth revisiting.
    Dusty
  14. Replies
    290
    Views
    11,360

    "I'm gonna figure out a consistent way to get a...

    "I'm gonna figure out a consistent way to get a cast-looking finish on all the permanent mold parts."
    Steel shot in a serious industrial blaster is the old standard. A company that repaints water...
  15. Replies
    12
    Views
    332

    You want the bigger manifold the Trike manifold...

    You want the bigger manifold the Trike manifold and carb were kind of subpar for Meter Maid work much less a bobber. I'll dig through my junk, I think I have one in my swap meet stuff if I didn't...
  16. Replies
    12
    Views
    332

    Cotten who is usually over on S&S Vintage Tech...

    Cotten who is usually over on S&S Vintage Tech Forum is a Linkert & Schebler restorer and fountain of knowledge. Tell him what you are building and how you plan to use it. I'll bet he can tell you...
  17. Don't tease the troll

    Don't tease the troll
  18. Replies
    16
    Views
    543

    Anymore all I build Is Sport Scouts. So I set the...

    Anymore all I build Is Sport Scouts. So I set the engine in a chair and bolt the front frame section on.
    https://i.postimg.cc/fLQ3kbVV/0226111854a.jpg
    Then the rear section, forks and etc. etc.
    ...
  19. Replies
    16
    Views
    543

    I always put the engine on its side on some...

    I always put the engine on its side on some blocks to level it, then laid the frame over the engine hung a few bolts then tilted it upright. Made it way easier to avoid scratches and chips and back...
  20. Replies
    52
    Views
    987

    For tapered shafts I assemble them without the...

    For tapered shafts I assemble them without the key hand tight and measure or mark the installed depth. If they go to the same depth with the key it's probably good to torque if not it's time to break...
  21. Replies
    26
    Views
    3,043

    I used 1" .125 wall resistance welded tube on...

    I used 1" .125 wall resistance welded tube on this XJ. I can't see any reason to pay extra for DOM unless you are doing a bunch of slip fit joints. The the tiny increase in strength from work...
  22. House of Horsepower ...

    House of Horsepower http://forum.sscycle.com/viewtopic.php?f=3&t=13038
    Dusty
  23. If you click the little triangle on the lower...

    If you click the little triangle on the lower left, you can tag them as spam. Then Lisa will delete them and the spammer.
    Dusty
  24. Replies
    18
    Views
    826

    Clean that neck up and get us a good pic. What...

    Clean that neck up and get us a good pic. What I'm seeing doesn't look like a machined recess. Looks more like a ball race for something.
    Dusty
  25. The UB1250 battery at less than $20.00 lasts 3 or...

    The UB1250 battery at less than $20.00 lasts 3 or 4 years in my kick only with battery ignition.
    Dusty
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in