CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: JBinNC

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    5
    Views
    58

    I've got a similar tool from Champion Spark Plug...

    I've got a similar tool from Champion Spark Plug that is shaped like a ball point pen and is at least 50 years old. It has a little neon(?) tube in it that flashes with the spark. Very handy.

    Jim
  2. Replies
    33
    Views
    560

    Because air cooled motors are different animals....

    Because air cooled motors are different animals. And more importantly, the H-D combustion chambers are primitive compared to what they are doing with the car motors. And most importantly, that's an 8...
  3. Replies
    33
    Views
    560

    Good luck with it, but that ain't gonna happen. ...

    Good luck with it, but that ain't gonna happen.

    Jim
  4. Replies
    4
    Views
    81

    A little help from a friend: The front...

    A little help from a friend:

    The front cylinder has 120-48 cast into the base. The "50 front cylinder may have this as well. The rear cylinder has no marks at all.

    Jim
  5. Replies
    4
    Views
    81

    No numbers or identifying marks at all on the '48...

    No numbers or identifying marks at all on the '48 and '49 cylinders as far as I can remember, and I just finished up a '48 and a '49 a few months ago.

    Jim
  6. Replies
    33
    Views
    560

    1)The expectation of 90 ft.lb. is not realistic. ...

    1)The expectation of 90 ft.lb. is not realistic.
    2) As you increase stroke, vibration goes up. That is simple physics, and you cannot balance your way around it.
    3) As compression goes up,...
  7. Replies
    10
    Views
    177

    You have a factory H-D steel hub and a factory...

    You have a factory H-D steel hub and a factory H-D steel, drop center 16" rim, so spoke sets for those are plentiful. You could reuse the existing spokes in a pinch, although that is not usually...
  8. Replies
    9
    Views
    100

    Yes, I think that's it. Works perfectly. Jim

    Yes, I think that's it. Works perfectly.

    Jim
  9. Replies
    33
    Views
    560

    Hey, the OP says he's a machinist. Jim

    Hey, the OP says he's a machinist.

    Jim
  10. Replies
    9
    Views
    100

    I have one that is a step above that one, that...

    I have one that is a step above that one, that also integrates the brake light function in the rear turn lamps. I think your existing black box does the same, judging by the wires shown in your pic....
  11. Replies
    33
    Views
    560

    Ah, the 9028 bearing. MUCH easier to do than the...

    Ah, the 9028 bearing. MUCH easier to do than the 9029 that the OP proposed.

    Jim
  12. Replies
    9
    Views
    100

    The Signal Dynamics module I have is the size of...

    The Signal Dynamics module I have is the size of a Zippo lighter and replaces the black box in your pic, the flasher, and the load equalizer. Two wires must be extended to the front turn lamps to get...
  13. Replies
    9
    Views
    100

    You will probably have to do some rewiring...

    You will probably have to do some rewiring whatever components you end up using. The modern modules eliminate the need for the load equalizer for LEDs, so it should be simpler overall.

    Jim
  14. Replies
    26
    Views
    682

    Poll: In the old days, post WWII, a top brand, right up...

    In the old days, post WWII, a top brand, right up there with SnapOn. I don't know how they rate now. I've got some Cornwell from my dad's tool set.

    Jim
  15. Replies
    9
    Views
    100

    Looks like a turn lamp/brake lamp adapter box....

    Looks like a turn lamp/brake lamp adapter box. Doesn't really matter what kind it is. There are several offered. I like the Signal Dynamics box on my WG. It auto-cancels on a timer, and combines the...
  16. Replies
    5
    Views
    199

    Optional on most years, standard on the '71 & '72...

    Optional on most years, standard on the '71 & '72 FX and the Low Riders (FXS) through '84 I think.

    Jim
  17. Replies
    35
    Views
    677

    Just use the punch that you are drifting the pin...

    Just use the punch that you are drifting the pin in with. Move over half the hole and upset the top of the bushing with a light blow.

    You can Loctite the bushing in place as well. No real need to...
  18. Replies
    8
    Views
    177

    I like the Dyna S as well, have them in both my...

    I like the Dyna S as well, have them in both my bikes. But like anything electronic, they do fail. They will usually manifest an intermittent miss after the motor is warm, and sometimes do stop...
  19. Replies
    10
    Views
    228

    The VOES diminishes or eliminates the tendency to...

    The VOES diminishes or eliminates the tendency to spark knock in hot weather.

    If you are going to eliminate the VOES, grounding the VOES wire from the module is the correct way, as you have done....
  20. Replies
    18
    Views
    610

    Best line from farmall's exposition: "I could...

    Best line from farmall's exposition:

    "I could buy a new dually for cash but that's because I would never buy a new dually for cash."

    Listen up boys & girls because there is A LOT of wisdom in...
  21. Replies
    10
    Views
    228

    Check the VOES for a vacuum leak, for electrical...

    Check the VOES for a vacuum leak, for electrical function, and that it is grounded. Your bike is at the age where the VOES start to fail.

    Check your full advance timing at the flywheel with a...
  22. Replies
    3
    Views
    112

    The measurements from the manual for positioning...

    The measurements from the manual for positioning these rims are only good for the OEM factory rims. For anything else, I have found that centering the rim between the spoke flanges on any of these...
  23. Replies
    33
    Views
    560

    An attempt was made to do that on the pinion side...

    An attempt was made to do that on the pinion side to control crank flex in race motors. I don't think it proved successful. On the old big twin fuel motors they do away with the pinion bearing and...
  24. Replies
    33
    Views
    560

    Yeah, I'm a machinist too, and one of the things...

    Yeah, I'm a machinist too, and one of the things my old boss often said, was, don't reinvent the wheel. Before you cut up a good case, get a '58 - '69 left case so you can see what is involved. The...
  25. Replies
    33
    Views
    560

    You would be better off mating a '58 - up...

    You would be better off mating a '58 - up generator left case to your right case if you really want the Timken bearing.

    Jim
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in