CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: 69Glide

Page 1 of 8 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    32
    Views
    1,001

    This was a hot rod shovelhead 80" motor... I...

    This was a hot rod shovelhead 80" motor...

    I built this motor and I tuned this motor. I know that it was correct as far as piston to cylinder clearances, all bearings and bushings fitted up...
  2. Replies
    347
    Views
    36,329

    This was probably a birthday ride when she was 3...

    This was probably a birthday ride when she was 3 or 4 - I don't remember for sure..

    She was 41 on May 2nd..

    Time flies...

    110717

    110718
  3. Replies
    32
    Views
    1,001

    VOES or Not It depends where you ride , when...

    VOES or Not

    It depends where you ride , when you ride, how hard you ride, how much you ride...

    Las Vegas in the summertime. Pulling the Baker Grade with some buds. 960 Feet ASL to 4130 Feet ASL...
  4. Anyone? Recognize The Artist Or These Drawings?

    I was given a set of 4 pen and ink drawings back in the early 80's. They are original pen and ink on high quality rag paper, 8 x 10 inches. Signed by "CTM, or "CJM", 81. I've never seen them...
  5. That looks like material from a sintered bronze...

    That looks like material from a sintered bronze or aluminum filter element. Very common in fuel filters. Not sure how that could have gotten in the motor.. Do you know the history of the motor?

    Is...
  6. Replies
    12
    Views
    799

    I don't know. I only have experience with the...

    I don't know. I only have experience with the original Harley throttle. I picked up the Nash throttle for another project but decided to do something different. I can say that the Nash is secured by...
  7. Replies
    12
    Views
    799

    On my setup it does not. The stock HD internal...

    On my setup it does not. The stock HD internal throttle uses a hard wire inner instead of a flexible braided cable and has both ends of the outer casing secured so it is a push/pull throttle. I use a...
  8. Replies
    12
    Views
    799

    44 mm SE CV...

    44 mm SE CV...
  9. Replies
    12
    Views
    799

    I use the stock HD internal throttle with the...

    I use the stock HD internal throttle with the solid wire. My preference - it stays where I put it. Great thing on long trips I don't have the constant pull from the return spring...

    110566
    ...
  10. Replies
    7
    Views
    369

    That carb should be a Keihin not a Bendix.. ...

    That carb should be a Keihin not a Bendix..

    Jim is right on about the causes -

    This is a photo of the tube inside of the bowl - you can see where this one has been soldered. Most of these will...
  11. This is a Baker 6in4 that I installed in my FLH...

    This is a Baker 6in4 that I installed in my FLH in 1991. It had well over 130K miles on it when this happened... I had opened it up a couple of times during those years - new seals and bearings at...
  12. Replies
    42
    Views
    11,811

    Poll: Mine - Sound up... ...

    Mine -

    Sound up...


    https://youtu.be/i3K1vXVn-VA

    69
  13. Replies
    347
    Views
    36,329

    Ride With Your Kids

    110213


    110214
  14. Replies
    347
    Views
    36,329

    Remember MMA (Modified Motorcycle Association) - Pre ABATE

    Wife took these at an AMA (pre ABATE) run and party at Live Oak Springs in East San Diego County...

    110208
    My best bro and I firin' up a bowl - I'm on the right edge, almost out of the frame.

    ...
  15. Replies
    347
    Views
    36,329

    I put a lot of miles on this daily rider - 84"...

    I put a lot of miles on this daily rider - 84" stroker...

    San Diego 1978 ish...

    Good riding weather almost every day. I would go for weeks without driving a cage...

    110206

    110207
  16. Replies
    347
    Views
    36,329

    Took this a few years back - this mural has been...

    Took this a few years back - this mural has been gone for awhile now and my 69 is in a different configuration...

    110110
  17. Jim - You are right.. I can't find any offset...

    Jim -

    You are right.. I can't find any offset info on the early models - rigid frame and hydra glide and early Duo-Glide. But I found offset measurements and specs for later FLH and Softails. I...
  18. We will just have to disagree. I would need to...

    We will just have to disagree.

    I would need to see the MoCo factory information, until then I am confident in my analysis and conclusions based on my almost half a century of experience with these...
  19. Respectfully to all but I disagree. This...

    Respectfully to all but I disagree.

    This question comes up often and has for years.

    I believe that by design the wheels are not offset but are designed so that the centerline of the tires...
  20. Replies
    96
    Views
    9,368

    Memory is a strange thing. I'm 68 and I've...

    Memory is a strange thing. I'm 68 and I've probably forgotten more things than I remember - but some things are still crystal clear.

    I've always been a huge fan of live music - and I remember...
  21. Replies
    96
    Views
    9,368

    We saw that show in San Diego. August 1st, 1975....

    We saw that show in San Diego. August 1st, 1975. Old Balboa stadium just down the hill from Balboa Naval Hospital - it was Fleetwood Mac, Rod Stewart & The Faces, Loggins and Messina, and Lynrd...
  22. Replies
    10
    Views
    566

    Measure the stroke - Top Dead Center to Bottom...

    Measure the stroke - Top Dead Center to Bottom Dead Center. You need to verify that you still have EL flywheels..

    Since you have no history on the motor you may have FL flywheels and not know it.....
  23. Replies
    12
    Views
    1,366

    Very cool. Military service is an honorable...

    Very cool. Military service is an honorable thing. I've always felt good about mine, I'm sure you do as well. My youngest son just got out of the Navy. He was in for 9 years was a sonar tech on...
  24. Replies
    12
    Views
    1,366

    I was a Tradevman. I worked on simulators as a...

    I was a Tradevman. I worked on simulators as a junior enlisted. I was an instructor after I made E6. I taught basic and advanced ship control and navigation to submarine crews at Sub Base Ballast...
  25. Replies
    347
    Views
    36,329

    Breakfast In Tecate - Early Eighties

    109014

    ..

    109015


    ..

    109016
Results 1 to 25 of 190
Page 1 of 8 1 2 3 4

Log in

Log in