CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: jsaz666

Page 1 of 9 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    7
    Views
    639

    If it continues to bend, I have had very good...

    If it continues to bend, I have had very good luck with the banjo bolt switches. I usually find them for $20 or so.
  2. Replies
    8
    Views
    944

    Also from the limited view of the pic, is that a...

    Also from the limited view of the pic, is that a 5 speed in there?
  3. Replies
    8
    Views
    944

    This man speaks the truth. I have been through...

    This man speaks the truth. I have been through MANY $99 sets of kicker gears until I spent the money on Baker gears (which would've been cheaper in the long run), and now I own a Baker 6 into 4...
  4. Best tool for removing steering head bearing races

    I FINALLY got around to changing my steering head bearings on my 07 softail this weekend, and I could not for the life of me, get at the bearing races IOT pound them out. I would normally run a bead...
  5. Replies
    25
    Views
    4,282

    I was on the phone with BDL about 2 weeks ago...

    I was on the phone with BDL about 2 weeks ago ordering a new clutch hub and I was told that there has been a problem for years with aftermarket frames having the center post in the wrong location and...
  6. Yep, evo sportster boxes will work, and to the...

    Yep, evo sportster boxes will work, and to the guy looking really close it's a really neat change IMO. I also have a jammer frame with a REALLY tight clearance on the rear box and had to shave a bit...
  7. Replies
    3
    Views
    535

    A new Sissy bar is on the list before spring.

    A new Sissy bar is on the list before spring.
  8. Replies
    3
    Views
    535

    Made some progress today. Got the bars mocked...

    Made some progress today. Got the bars mocked up, checked the length of throttle cable, brake line and wiring, and the wiring is the only thing I need to redo. That's fine, since the initial wiring...
  9. Thread: Evo Chopper

    by jsaz666
    Replies
    7
    Views
    1,532

    You are going to want to pull that EZ clutch when...

    You are going to want to pull that EZ clutch when you go to a foot clutch. It makes it so light, you can't feel the clutch spring through a boot.
  10. Replies
    3
    Views
    535

    Built some new handlebars

    There was some 1" round bar in the garage, and a tubing notcher I got for christmas I hadn't tried yet, so what the hell! I'm not 100% sold on the "pointy" tops yet, it looked way better on paper. ...
  11. Replies
    32
    Views
    1,361

    HAHA!! That was awesome! I don't know weather...

    HAHA!! That was awesome! I don't know weather to laugh or get a second opinion on my over 40 physical........
  12. Replies
    32
    Views
    1,361

    OK, I get the green loctite on the shaft, but why...

    OK, I get the green loctite on the shaft, but why the acid? Etch/clean the surface for better adhesion?
  13. Replies
    32
    Views
    1,361

    I had to look pretty close at first to even...

    I had to look pretty close at first to even notice it had spun. I noticed the problem when I went to kick it over in the morning (soon after the afore mentioned situation) heading to work and the...
  14. Replies
    32
    Views
    1,361

    Yeah, I'm not always the most responsible or...

    Yeah, I'm not always the most responsible or cautious.....
    .
  15. Replies
    32
    Views
    1,361

    Burnouts may have happened........

    Burnouts may have happened........
  16. Replies
    32
    Views
    1,361

    It wasn't loose enough to cause a wobble, just...

    It wasn't loose enough to cause a wobble, just enough to cause the taper to slip is my guess.
  17. Replies
    32
    Views
    1,361

    1.5" or 3" belt open primary?

    I broke my chop again..... it's an evo powered rigid with a baker 6 into 4 trans, kick only and 1.5" open belt primary. The mainshaft nut on clutch drum backed off and sheared the woodruff key. ...
  18. Replies
    12
    Views
    4,792

    I know what you are dealing with Brother. I was...

    I know what you are dealing with Brother. I was t-boned by a douche in a F-150 that ran a stop sign at 40. I was wearing a shitty little half helmet, but it saved my life- I still bled out on the...
  19. Replies
    56
    Views
    4,719

    Painthuffer Metalflake Rules

    Painthuffer Metalflake Rules
  20. Before- 79122 After- 79123 Thats as...

    Before-

    79122

    After-

    79123

    Thats as she sits now, and as we all know, they are never "done".
  21. Hows this? Apparently that guy thought a red...

    Hows this? Apparently that guy thought a red sign with white means yield......... He was only doing 40 when he hit me. I alive, just lots of cool scars.
    79113

    So here is the real story- around...
  22. Replies
    10
    Views
    959

    How? Any filter?

    How? Any filter?
  23. Replies
    10
    Views
    959

    GOT IT! A combination of material removal from...

    GOT IT! A combination of material removal from the top of the box, a little more from the rocker arm bolts and a tiny bit more from the underside of the backbone and it all fits- barely. I just...
  24. Replies
    10
    Views
    959

    Yeah, I need about 1/2" more clearance on the...

    Yeah, I need about 1/2" more clearance on the backbone the entire length of the rear box.
    what would be the best way to clearance it? Heat and hammer or cut and add a flat plate? If I have to...
  25. Replies
    10
    Views
    959

    For clarification, I have 91-03 3 piece boxes. ...

    For clarification, I have 91-03 3 piece boxes. There is NO WAY a 2 piece cover would fit. I called it quits last night before the 4lb deadblow came out of the toolbox. I had some 84-91 big twin...
Results 1 to 25 of 216
Page 1 of 9 1 2 3 4

Log in

Log in