Search Forums:

found this:

Harley-Davidson OHV Engine Displacement
To use this Chart
1. Find your bore size in Column 1.
2. Move right to Column 2 to the exact size for boring (decimal)
3. Select your...

It looks like in your pic, you are gonna weld a tab to the frame for the caliper to sit on, nothing to actually hold the caliper - I don't like it.

Can you swing the caliper around so it sits...

Thanks for that;

https://thehoglegend.com/news-magazine-articles/

Desmohog; Ducati 900ss heads on Evo bottom at Crossbreed Cycles:

109168

109169

109170

http://crossbreedcycles.net/home--contact.html

Note the bottom spring seats over the lower spring perch, and how the radius is inside the top of the front legs at the lower spring perch - it is a Jammer springer:

109125

109127

Worth...

what is it you are looking to find?

As MOTher noted above:

Disc Rotor Spacer
".040" thick spacer is used to re-establish correct rotor-to-caliper alignment and spacing when ever servicing wheels, brake calipers, supports or rotors...

how about a pic of the whole frame. is it a softail?

The end of that red wire at your points looks sloppy; kinda bare and scraggly - is it making full contact with the points? does it need a new connector on there to ensure positive connection?
that...

Sportster neck gusset removal?

https://www.jockeyjournal.com/forum/showthread.php?p=882237

Saw this 2002 Sporty neck stripped on a JJ thread:

109104

109105


As Jim noted; back in the '70s, Santee was one company that made hardheads to stretch and rake neck:

109106

Got a manual?
page 149 here is start of kickstart info, in the gearbox section:
https://justpanhead.com/wp-content/uploads/2013/08/Factory-HD59-69-Pan-Shovel-Service-Manual.pdf

are both the front and back legs straight?
are the holes at the bottom of the legs round - not egg shaped?
are the holes in the rockers ("blades") round, not egg-shaped?
Are the holes in the...

according to 1940 service manual, which includes UL, breaker cam gear may not be in original position if it has been replaced so original marks will not align, disregard timing marks.

set advanced...

seen this:

Thread: Welder choice final two

farmall: "Check welding forums like Weldingweb. Their users have a wide variety of machines.

https://weldingweb.com/vbb/forumdisp...ponsored-Forum...

If you search what you want, you will find more than you need or want...a quick search at Miller Welds got this:

Buying Your First Welder: A Practical, Informative Guide for Do-It-Yourselfers
...

You say you are running them, but need custom mounts...not sure what that means...perhaps I'm a bit daft.

these are to fit shovel and pan:

Ohlins Blackline Reservoir Shocks
" They are designed...

May just need to get new tapered roller bearings(cups) to fit into your tapered roller bearing races (cones), then measure length of neckpost needed - maybe just slug yours to lengthen if needed, or...

Seen this?

Sportster Street Tracker GSXR Fork Swap!
"'95 Sportster...2007 GSXR 1000 Forks from good ol eBay...Cognito to supply the new steering stem and proper bearing kit for the Harley...

108869

Just curious if you did a compression test before you pulled it apart - if so, what was it at?

What is the symbol and number below 'ZE-35T'?

found this:

"The neck of the frame displays the casting code ZE-35T A4, indicating that the frame was produced between late 1941 and early 1942,...

Thread: Rigid Frame Axle Length?

"Anybody know the length of a stock panhead axle for a RIGID frame?

I'm going to a swap meet tomorrow and would like to be able to verify by measuring....

Yup, it's just like Dusty says;
I run one hot to the middle terminal on one side and a jumper wire to the middle terminal on the other side .
On one side is headlight; upper terminal is low beam,...

" Case Numbers

Please feel free to comment good, bad, or informational on any of the photos in this album. We hope this database of numbers will help educate people in the vintage motorcycle...