CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: 47str8leg

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    19
    Views
    326

    I’m a firm believer in keeping everything here...

    I’m a firm believer in keeping everything here related to American sub-culture.
  2. Why , for the love of God , has the crackheads...

    Why , for the love of God , has the crackheads iconic skull and crossbones addition been removed ?
  3. Replies
    22
    Views
    572

    Ditto.

    Ditto.
  4. On vacation this week in Melbourne Beach and Vero Beach Fla.

    Visiting family for Thanksgiving. Any good biker bars around here at all ?
  5. I have a set if brake shoes from my sons old 2005...

    I have a set if brake shoes from my sons old 2005 50cc Honda dirtbike I can check if you have any reference points to go from.
  6. Replies
    13
    Views
    302

    I prefer paint over powdercoat as well.

    I prefer paint over powdercoat as well.
  7. Replies
    13
    Views
    302

    Talked plenty about powdercoating and paint prep...

    Talked plenty about powdercoating and paint prep on here but I’ll say it again .
    Do all the prep work yourself and save a lot of headaches later on. Put bolts in all threaded holes. Any spot you...
  8. Thread: Pipes.

    by 47str8leg
    Replies
    2
    Views
    153

    As I’ve mentioned before on the subject of...

    As I’ve mentioned before on the subject of muffler shops bending pipe for you. Make an appointment first so it gets done in the same day.
    Bring your frame with the motor and tranny on it ( on a...
  9. Replies
    38
    Views
    1,424

    ^^^^ Read this entire thread. There is plenty...

    ^^^^
    Read this entire thread.
    There is plenty that is his fault.
  10. Money isn’t everything but it doesn’t hurt to...

    Money isn’t everything but it doesn’t hurt to have when used properly.
  11. Well, it’s s visual train wreck in my eyes but ,...

    Well, it’s s visual train wreck in my eyes but , who gives a fuck ?
    You’re building everything and riding the wheels off the fucker ( though I don’t recommend Chinese parts on anything ).
    Great...
  12. Replies
    8
    Views
    440

    Its an electrical “proximity “ tester. I have...

    Its an electrical “proximity “ tester.
    I have one that’s built into the top of my small volt/ohm meter I carry in my bike tool bag.
    106246
    106247
  13. Alec Baldwin should have shot the woman in Houston

    Piece of shit abandoned her kids and one 9 year old was left dead in the apartment the kids were living in for a year while the others were left fending for themselves for the most part.
    To top it...
  14. Replies
    108
    Views
    4,185

    106057

    106057
  15. Replies
    36
    Views
    776

    The transmission adjuster is in its correct spot...

    The transmission adjuster is in its correct spot in the relief of the plate but when the transmission is on the plate the open side of the adjuster faces up.

    So , youíre bolting your transmission...
  16. Replies
    36
    Views
    776

    Thst transmission is bolted to the wrong side of...

    Thst transmission is bolted to the wrong side of the plate.
  17. Replies
    8
    Views
    384

    Circuit breaker or ignition switch. Disconnect...

    Circuit breaker or ignition switch.
    Disconnect your wire from the switch to the coil ( tape it up so it canít contact anything) and run a jumper wire straight from the battery positive to the coil...
  18. Replies
    3
    Views
    283

    Hey,ho,way to go Ohio.

    Hey,ho,way to go Ohio.
  19. Replies
    108
    Views
    4,185

    First degree murder charges will never stick. I...

    First degree murder charges will never stick.
    I wouldn’t talk to reporters either. They only turn against you using soundbites and clips of footage showing you in a bad light so I can’t blame him...
  20. Replies
    9
    Views
    1,039

    Yes. I’ve had no problems.

    Yes. I’ve had no problems.
  21. Replies
    8
    Views
    604

    Donít get the standard 8mm set up , Order it with...

    Donít get the standard 8mm set up , Order it with 1 tooth smaller pulley. That set has always run too tight. Canít tell you how many times Iíve heard of those breaking under a covered tin primary due...
  22. Replies
    4
    Views
    322

    Thanks for the responses guys. Jim - I thought...

    Thanks for the responses guys.
    Jim - I thought about adjusting the bracket but felt I wouldn’t be able to line it up with the groove on the carb pulley afterwards . Maybe I’m just not understanding...
  23. Replies
    4
    Views
    322

    Panhead carb and tin questions

    105227

    Question #1 - S&S Super E carb needs a spacer block because the throttle pull cable wonít clear the head. S&S has two size blocks Iím aware of. Iíd like to use the shorter spacer block but...
  24. Replies
    20
    Views
    776

    I tried so check your messages when you get a...

    I tried so check your messages when you get a chance
  25. Replies
    20
    Views
    776

    Drags and Jim ( Jim , sent you a P.M. but I don’t...

    Drags and Jim ( Jim , sent you a P.M. but I don’t think it went through ),

    Some things just can’t be discussed in public and no , nobody on any motorcycle board is involved.
    Is there any other...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in