CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: DustyDave

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.03 seconds.

  1. Replies
    8
    Views
    203

    If you pull the timing plug then turn the crank...

    If you pull the timing plug then turn the crank pin down to the bottom and fill the crankcase with cheap atf then fill the cylinders with atf things will be as protected as possible. Of course if you...
  2. Replies
    11
    Views
    225

    Look over the seals with a magnifying glass....

    Look over the seals with a magnifying glass. Quite often the numbers are cast in the rubber.
    Dusty
  3. Replies
    172
    Views
    23,901

    Testing the hydraulic clutch. It releases enough...

    Testing the hydraulic clutch. It releases enough to turn the sprocket by hand with it in 1st gear. If I was going to build another I would increase the slave cylinder area a little it's a little...
  4. Replies
    172
    Views
    23,901

    Whittling the hex out with the mill down takes a...

    Whittling the hex out with the mill down takes a little creative use of tools.
    https://i.postimg.cc/5yNzZR3z/20201007-153416.jpg
    Dusty
  5. Replies
    107
    Views
    5,501

    I graduated three times between 1966 and 1969...

    I graduated three times between 1966 and 1969 from Oklahoma State University School of Technical Training.They didn't call it an accociates degree back then] all I got was a certificate of...
  6. Replies
    172
    Views
    23,901

    No valve relief unless I decide to change to a...

    No valve relief unless I decide to change to a normally asperated gas class!

    know that there is a release bearing holder in that bar just got ta keep whittling....
  7. Not motorcycle but at least it has a motorcycle emblem

    My wood butcher finally finished my custom cedar door after only eight years.
    https://i.postimg.cc/rsjkHZm7/20200929_122901.jpg
    It's hard to tell from these pictures but the Indian Motocycle...
  8. Replies
    172
    Views
    23,901

    Started making the head studs out of grade 8...

    Started making the head studs out of grade 8 bolts. I'm cutting each one to be a tight fit in the cylinder. So far most are .002 to .0035 oversize.
    https://i.postimg.cc/nrHJxTYt/20200929-133325.jpg...
  9. Replies
    172
    Views
    23,901

    Made the head washers out of 4140 just coz I had...

    Made the head washers out of 4140 just coz I had it.
    https://i.postimg.cc/Fz9KJk74/20200928-143208.jpg
    Dusty
  10. Replies
    172
    Views
    23,901

    Got a little sumptin done this week...

    Got a little sumptin done this week
    https://i.postimg.cc/hjW5ZTxW/20200926-170953-1.jpg
    https://i.postimg.cc/fyMgDsB8/20200926-171028-1.jpg
    Dusty
  11. Replies
    4
    Views
    406

    Want me to write your insurance company and tell...

    Want me to write your insurance company and tell them that it's a 4 hr straighten job and that you don't need a new frame?:D;);)
    Dusty
  12. Replies
    162
    Views
    4,388

    Dam!! What did he do to you? Dusty

    Dam!! What did he do to you?
    Dusty
  13. Replies
    172
    Views
    23,901

    Got the crank assy balanced this morning. And...

    Got the crank assy balanced this morning. And forund out right away that I didn't have any of the thrust washers I needed to centralise the flywheels in the case so I went to get my piece of 4140...
  14. Replies
    8,915
    Views
    355,168

    No Idear who he is but he stole all my whiskey n...

    No Idear who he is but he stole all my whiskey n Pills
    https://i.postimg.cc/wBPnkZsG/20200914-213054-1.jpg
    If'n any body else wants one Ya gots ta send me an address Jessy has his address all over...
  15. I prefer the mini Denso the Suzuki densos came in...

    I prefer the mini Denso the Suzuki densos came in two versions the ammeter version needs a full 12v to the voltage reference and the idiot light version must have the same resistance as the idiot...
  16. Replies
    8,915
    Views
    355,168

    Hay Step N Fetch it, I can send you one of these...

    Hay Step N Fetch it,
    I can send you one of these bumper stickers! With this on your bumper people will think that like Bill if you screw up enough you finally figure it out!...
  17. The self exciting Mini Denso is internally...

    The self exciting Mini Denso is internally rectified and regulated with only a wire to the battery needed. Unless you have a thing for idiot lights. The Suzuki alternator needed more wires. The...
  18. Yep, You can get them from 35 amps to 100 amps or...

    Yep, You can get them from 35 amps to 100 amps or so. I've been getting 70s lately cuz they are cheaper and the extra amperage doesn't seem to hurt.
    Dusty
  19. Thar's a mini denso one wire they are all over...

    Thar's a mini denso one wire they are all over fleebay.
    Dusty
  20. Replies
    8
    Views
    490

    Hard to tell through the comfuser. If it is water...

    Hard to tell through the comfuser. If it is water heating a small amount on the stove will produce steam and clear the oil. If it is metal it won't clear.
    Dusty
  21. Replies
    8,915
    Views
    355,168

    Honest to God the Cheeto compared a bad golf shot...

    Honest to God the Cheeto compared a bad golf shot to the police shooting someone in the back 7 times!
    ”Shooting the guy, shooting the guy in the back many times, I mean, couldn’t you have done...
  22. Proly when ya think 2.5 to 4 million dollars is...

    Proly when ya think 2.5 to 4 million dollars is toy money. That seems to be the range of asking prices for the few that I could find for sale.
    Dusty
  23. The Amen Saviour is a much more durable...

    The Amen Saviour is a much more durable suspension, way cheaper and already some are already set up for hardly trannys just need to fab chief mounts the right distance in front. If you have never...
  24. Here's the link I left out...

    Here's the link I left out
    http://zenoswarbirdvideos.com/F4U.html
    Dusty
  25. Have you ever made the mistake of going to Zeno's...

    Have you ever made the mistake of going to Zeno's Warbirds? You can lose hours down that bunny hole I think that the best was the one that taught me how to assemble a P47 without any specialized...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in