CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Sugarcubes

Page 1 of 9 1 2 3 4

Search Forums: Search took 0.03 seconds.

  1. Replies
    4
    Views
    178

    you might have over adjusted the throw on your...

    you might have over adjusted the throw on your shift pedals and pulled the pawl adjustment out of whack, meaning that the shifter pawl arm has come off of the shifter drum and isn't properly engaging...
  2. Replies
    5
    Views
    368

    Jim mentioned the cases which was something he...

    Jim mentioned the cases which was something he also advised me about. I have a later motor being a 1996 which is apparently a little bit thicker in the case which would allow for future upgrades like...
  3. Replies
    5
    Views
    368

    I was in your position last year and was deciding...

    I was in your position last year and was deciding whether or not to upgrade my 80" evo. I weighed up the costs vs benefits of putting in a new big block from S&S or put some work into the stock...
  4. Sticky: I like how that sits as is. If it were me, Id put...

    I like how that sits as is. If it were me, Id put a medium height sissy on it (nothing too tall) and some 4" risers with a drag bar on it
  5. Replies
    3
    Views
    180

    I replaced my seal and spacer a couple weeks ago...

    I replaced my seal and spacer a couple weeks ago due to changing to an open belt BDL drive (spacer needs to be installed backwards).
    I used a Jims spacer and yes it does slide on relatively easily...
  6. Replies
    2
    Views
    246

    Do you mean that the belt is hanging off 1/8" of...

    Do you mean that the belt is hanging off 1/8" of an inch inwards toward the motor? If so, mine did the exact same thing. Under throttle the belt would move towards the outside (away from the motor)...
  7. You can always have a "custom" job done to get...

    You can always have a "custom" job done to get any wheel to fit depending how much money you want to throw at it.
    Theres various options for your harley, I like a plain old fashioned 21 star hub...
  8. Replies
    43
    Views
    1,448

    My throttle cable on my ironhead snapped leaving...

    My throttle cable on my ironhead snapped leaving the Trip Out a couple years back. I managed to get about 10 miles along the road by holding the bare cable in my hand before it started wearing...
  9. Replies
    4
    Views
    310

    I did wonder if that might be the case! I will...

    I did wonder if that might be the case! I will follow the chart provided by TriNortchopz and go lightly with it.

    Thanks fellas
  10. Replies
    4
    Views
    310

    classic / repop springer service

    evening all.

    I'm doing a bit of maintenance on my repop harley springer (same type as an early hd) and was looking for some advice on a few bits. All I can find are service guides on the later...
  11. Replies
    15
    Views
    446

    I wouldn't waste time playing with spacers or...

    I wouldn't waste time playing with spacers or spending the cash getting a perfectly good springer cut up / extended / messed with.
    Stock length repop springers are always popular items and sell...
  12. Replies
    5
    Views
    461

    I've seen loads of guys build super pretty chops...

    I've seen loads of guys build super pretty chops that have all the chopular bits on them and look real nice parked on a show ground or in their Instagram pics. The reality is that a lot of them ride...
  13. Replies
    6
    Views
    293

    It does look like the belt has rubbed a little on...

    It does look like the belt has rubbed a little on the inner primary at the bottom, behind the clutch basket. The belt is in good condition and there isnt any noticable rubbing marks on the inside of...
  14. Replies
    6
    Views
    293

    that makes sense. The belt definitely isn't...

    that makes sense. The belt definitely isn't trying to come off, i just noticed that under throttle it definitely starts moving towards the outer edge of the pulley so I wasn't sure if this was an...
  15. Replies
    6
    Views
    293

    Hey Jim, thanks as ways for chiming in. So the...

    Hey Jim, thanks as ways for chiming in. So the stock factory washer that was behind the stator cover (alternator cover) is still there. The stock thin spacer that used to be in front of the rotor...
  16. Replies
    6
    Views
    293

    belt drive primary tracking question

    OK just to make sure all the necessary info is provided upfront - bike is a 1995 evo softail, I fitted a BDL 1.5" open primary belt drive kit a month or so ago.

    I'm still getting used to a lot of...
  17. Replies
    9
    Views
    1,990

    hey man I ride a softail chop myself after owning...

    hey man I ride a softail chop myself after owning a rigid 70s harley for 10 years. I love it! Your bike is awesome dont listen to any negativity
  18. Replies
    750
    Views
    324,699

    I was gonna go chain drive but to be honest I...

    I was gonna go chain drive but to be honest I couldn't justify the expense right now. The belt looks pretty new and they are built to last. Ive had chain drive Harleys and the lack of oil and grease...
  19. Replies
    750
    Views
    324,699

    pretty sure ive posted mine in here before a...

    pretty sure ive posted mine in here before a while ago but its been through some minor changes so il upload another whilst its sat here waiting for me to put the clutch pack back in

    105757
  20. Replies
    8
    Views
    172

    Thanks Jim. I wasn't sure if it needed to be in...

    Thanks Jim. I wasn't sure if it needed to be in pretty snug.

    Tattoo - 1995 evo 5 speed big twin
  21. Replies
    8
    Views
    172

    5 speed shift fork rod play?

    cant find anywhere in my manual where it states what the side to side play should be on the rod that the shifter forks slide on. Does anyone know?

    I'm making some upgrades to my transmission and...
  22. Replies
    30
    Views
    26,399

    couldn't tell you exactly but it moves it out a...

    couldn't tell you exactly but it moves it out a fair bit by probably 2 inches or so. The trap door is a solid inch thick of billet and the internals are sturdy with a good thick mainshaft extension...
  23. The front loop of the 90s evo softail frames look...

    The front loop of the 90s evo softail frames look pretty much the same as a straightleg frame. Its really only the rear swing section that needs addressing if you really must have a rigid. Me...
  24. In the UK it helps to keep the frame neck numbers...

    In the UK it helps to keep the frame neck numbers and motor numbers together for the V5.

    You could get one of the popular shops like Fenland Choppers to fab you up a frame but most places or even...
  25. Replies
    18
    Views
    6,562

    this is an interesting thread reading peoples...

    this is an interesting thread reading peoples different views and experiences. Ive worked desk based jobs for years because I fell into marine sales at a young age (family business) and by the time I...
Results 1 to 25 of 220
Page 1 of 9 1 2 3 4

Log in

Log in