CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: ncmc47

Page 1 of 5 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    12
    Views
    1,047

    Mufflers aren't for backpressure, they are to...

    Mufflers aren't for backpressure, they are to quiet your exhaust. I don't know who started the rumor you have to have backpressure to run right. A motor runs best with no back pressure, that's why...
  2. Replies
    6,019
    Views
    3,585,191

    Would be a bitch getting those seams straight!

    Would be a bitch getting those seams straight!
  3. Replies
    38
    Views
    1,870

    You believe what you want, around here most 8...

    You believe what you want, around here most 8 year olds know you don't point a gun a gun towards anyone and you don't place your finger on the trigger until you are ready to shoot.
  4. Replies
    38
    Views
    1,870

    Everyone should know to always check a gun to see...

    Everyone should know to always check a gun to see if it's loaded, even if the 10 other guys in the room checked it before it was given to you! If he wasn't such a libtard he would have known. He...
  5. Replies
    292
    Views
    11,668

    Say, would you list again what splined sprocket...

    Say, would you list again what splined sprocket shaft to run when using Knuckle Works left side case to short shaft tranny? With posts missing I can't scroll back and find it.
  6. Replies
    292
    Views
    11,668

    I was going to go with a grooved pinion bearing,...

    I was going to go with a grooved pinion bearing, like used to be advertised in the old biker mags. S&S advised to only make the groove 1/2 way around. Maybe taking oil from the heads? Probably one...
  7. Replies
    34
    Views
    885

    Are you sure that's a 48 frame? Looks more like...

    Are you sure that's a 48 frame? Looks more like what Palmer shows a 49, machining of the ride control stud. I'm relying on memory. I don't have it open in front of me. Not that it makes any...
  8. Replies
    34
    Views
    885

    Yes that's what I would do!

    Yes that's what I would do!
  9. Replies
    34
    Views
    885

    I'm not positive what you are doing, but I'll...

    I'm not
    positive what you are doing, but I'll take a stab in the dark. If you are trying to join 1 1/8th tubing to the joint where it turns to 1" as it goes towards the rear, instead of going...
  10. Replies
    6
    Views
    426

    There was at least on after market co. selling...

    There was at least on after market co. selling necks with the number boss. Don't remember if they sold frames that way, but they would certainly look AM if they did.
  11. Replies
    8
    Views
    856

    Gary, can't remember his last name. Very...

    Gary, can't remember his last name. Very knowledgeable guy. I think he goes by Smiley on this forum. I believe he has contact information on his site.
  12. Replies
    8
    Views
    402

    Way back when. I used 3in1 oil in the dash pots...

    Way back when. I used 3in1 oil in the dash pots of my MG.
  13. Replies
    16
    Views
    852

    Use a stethoscope or even a long screwdriver to...

    Use a stethoscope or even a long screwdriver to pin point where the noise is coming from. That will tell you a lot.
  14. Replies
    9
    Views
    636

    That kicker gear looks like it has been hot.

    That kicker gear looks like it has been hot.
  15. Were the condensers burning points? That's...

    Were the condensers burning points? That's usually the first sign they're going bad.
  16. Thread: Wide Glide

    by ncmc47
    Replies
    3
    Views
    373

    These are 41mm, much like what would be found on...

    These are 41mm, much like what would be found on a 50's Harley, no part number on the sliders so not a 49 part. The sliders are fairly shiney and the chrome on the tubes doesn't look like OEM.
  17. Thread: Wide Glide

    by ncmc47
    Replies
    3
    Views
    373

    Wide Glide

    I bought a set of sliders and tubes awhile back, just assumed they were OEM. The tubes have fairly decent chrome, but appear stock length. Then it dawned on me they could be after market. The only...
  18. Thanks JBinNC, for years I've told people that...

    Thanks JBinNC, for years I've told people that engines don't need back pressure to run best, only to be laughed at.
  19. Replies
    4
    Views
    413

    5 speed doesn't have overdrive in 5th, so it...

    5 speed doesn't have overdrive in 5th, so it won't drop your rpm. You maybe able to drop RPM with pulley change.
  20. Replies
    149
    Views
    9,328

    Thanks

    Thanks
  21. Replies
    149
    Views
    9,328

    Does anybody have contact info on Jeff Grossman...

    Does anybody have contact info on Jeff Grossman of Bull Dog Cycles? A quick search showed the heat cycles of bull dogs LOL! There were several on Face Book, but didn't find the right one, I guess.
  22. Replies
    13
    Views
    997

    Looks like it should work, do you have a ball...

    Looks like it should work, do you have a ball valve on the drain on your tank? Depending on the compressor you may need an elbow and and a 4 or 6 " piece of pipe to get the ball valve out where...
  23. Thread: 41 el

    by ncmc47
    Replies
    640
    Views
    25,465

    Pleas let us know what the problem was.

    Pleas let us know what the problem was.
  24. Replies
    43
    Views
    2,203

    The anchor rod should go to the solid leg of the...

    The anchor rod should go to the solid leg of the springer and level is much better.
  25. Thread: 41 el

    by ncmc47
    Replies
    640
    Views
    25,465

    Come on, inquiring minds need to know!

    Come on, inquiring minds need to know!
Results 1 to 25 of 122
Page 1 of 5 1 2 3 4

Log in

Log in