CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: DustyDave

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Nothing wrong with other brand tube assemblies...

    Nothing wrong with other brand tube assemblies they are usually much cheaper. But measure then measure again!! Don't forget that you will proly end up with a custom made axle - spacers and probably...
  2. Past experience says that if you don't measure...

    Past experience says that if you don't measure both tubes you are going to have problems. Nominal 39mm tubes run all over the place I put some Honda tubes in a Moto Guzzi triple trees and had to ream...
  3. That old wore out Atlas 12" quick change lathe is...

    That old wore out Atlas 12" quick change lathe is the best solution to odd ball threads I ever bought. I made a batch of 1 3/16" 24 tpi nuts the other day.
    Dusty
  4. Replies
    21
    Views
    8,603

    Not abnormal I learned to ride on a Indian...

    Not abnormal I learned to ride on a Indian military Scout that came from the factory that way. Lots of police departments set up their Harleys that way after Indian was gone. They seemed to think a...
  5. I bought a Indian 741 military scout that drove...

    I bought a Indian 741 military scout that drove fine absolutely a hands off rider and after I owned it foe years I had the rear fender off and discovered that the rear wheel was a little over an inch...
  6. Replies
    15
    Views
    342

    postimage.org seems to be friendly with even the...

    postimage.org seems to be friendly with even the pickiest website.
    Dusty
  7. Replies
    19
    Views
    7,967

    I give them a gmail address to send the pics to....

    I give them a gmail address to send the pics to. Duh didn't think mention that the first post. Proly forgot sumptin else but that's the joy of being old.
    Dusty
  8. Replies
    19
    Views
    7,967

    over at Vintage Tech it got so bad I was getting...

    over at Vintage Tech it got so bad I was getting 70 to 100 spammer and bott applications a day. I added a describe your bike and the ones that pass that I ask for a picture of them and their bike or...
  9. Replies
    6
    Views
    285

    https://www.youtube.com/watch?v=Pu1RTkWHA3o&ab_cha...

    https://www.youtube.com/watch?v=Pu1RTkWHA3o&ab_channel=Smooth-On
    I think this is the process that most small run lenses are made by. Be a lot of work and expense for one but then you would be able...
  10. Replies
    8
    Views
    303

    Take a piece of stainless steel gas welding rod...

    Take a piece of stainless steel gas welding rod and bend one up. Two pair of Vice Grips works well.
    Dusty
  11. Replies
    29
    Views
    1,453

    I came up behind a bicyclist on a 2 lane mountain...

    I came up behind a bicyclist on a 2 lane mountain road, going up the middle of the lane while I was test driving Los Alamos FD Ladder 1 . He seemed to be enjoying the line of cars behind him, so I...
  12. Replies
    6
    Views
    526

    Dam that's even worser that that GTO we got in...

    Dam that's even worser that that GTO we got in with 49500 miles on a 50000 mile warranty with 4 rods thrown one through the cross member we did save the intake though. Or the BMW with 2 fours that...
  13. Replies
    10
    Views
    411

    I don't have a Hardly to try one on but the ...

    I don't have a Hardly to try one on but the 224PPB102K Illinois Capacitor seems to be a good fit electrically for lots of apps. Somebody try one and let us know. It's really hard to pick one from a...
  14. Usually when there is an area all the way around...

    Usually when there is an area all the way around the piston with no carbon and heavy carbon in the center there is quite a bit of oil coming past the rings and washing the carbon off the edges. Think...
  15. Replies
    198
    Views
    27,264

    Getting a little closer to shape. The timer rides...

    Getting a little closer to shape. The timer rides on the outer bearing race that sets proud of the adapter with a slot and guide plate on the outside The reluctor mounting plates that allow each...
  16. Replies
    4,330
    Views
    333,886

    Have you ever listened to this without drugs? ...

    Have you ever listened to this without drugs?

    https://www.youtube.com/watch?v=CxCfnq7A56M&ab_channel=GratefulDead
    Tonight was only a little brandy n smoke.
    Dusty
  17. Replies
    4,330
    Views
    333,886

    I guess if Klondikekid64 can repeat on the same...

    I guess if Klondikekid64 can repeat on the same page, I oughter put the original In Hell I'll be in Good Company

    https://www.youtube.com/watch?v=B9FzVhw8_bY&ab_channel=TheDeadSouth
    Dusty
  18. Replies
    4,330
    Views
    333,886

    William Shatner covers Dead South ...

    William Shatner covers Dead South

    https://www.youtube.com/watch?v=r3P5JGr8WME&ab_channel=WilliamShatner-Topic
    Dusty
  19. Replies
    4,330
    Views
    333,886

    The rumors have persisted for years but never set...

    The rumors have persisted for years but never set to music before.

    https://www.youtube.com/watch?v=KG2SPjcKM4M&ab_channel=MusicFog
    Dusty
  20. Replies
    4,330
    Views
    333,886

    Got any old friends like this? ...

    Got any old friends like this?

    https://www.youtube.com/watch?v=-8sBe-_HtMs&ab_channel=ewecylinder
    Dusty
  21. You need to know how many kicks with the throttle...

    You need to know how many kicks with the throttle wide open to reach maximum compression reading on a engine at room temp that hasn't been started IE dry. and them with oil sprayed on the cylinder...
  22. Did you ever get compression readings wet and...

    Did you ever get compression readings wet and dry?
    Dusty
  23. Replies
    198
    Views
    27,264

    Centering the A-dapter plates (as Johnny Cash...

    Centering the A-dapter plates (as Johnny Cash said). Once they are centered I'll drill holes for the pins that will keep everything straight.
    https://i.postimg.cc/QtL6w6sj/20210222-121547-1.jpg...
  24. Dam that lathe was gone right away!

    Dam that lathe was gone right away!
  25. Wish this was a few hundred miles closer. ...

    Wish this was a few hundred miles closer. https://pittsburgh.craigslist.org/tls/d/conway-metal-lathe/7280762183.html
    Dusty
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in