CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Frog

Page 1 of 2 1 2

Search Forums: Search took 0.01 seconds.

  1. Thread: Cv carb cracked

    by Frog
    Replies
    4
    Views
    491

    If you know someone that can weld aluminum for...

    If you know someone that can weld aluminum for free, weld it up. If not, as suggested, buy another one. I paid $50 for the one I'm running. That was a good deal though.
  2. Replies
    17
    Views
    4,636

    I assume your using a jam bar. Heat her up (not...

    I assume your using a jam bar. Heat her up (not too hot so she glows red or anything) and apply steady pressure with your breaker bar. Might have to use a cheater pipe. When she starts coming...
  3. Replies
    20
    Views
    3,113

    How much do you weigh?

    How much do you weigh?
  4. Replies
    6
    Views
    2,808

    I just started year two with the Chevy Nova six...

    I just started year two with the Chevy Nova six cylinder points and condenser from one of those Chinese parts stores. Working well. Made in Mexico like the Blue Streaks.
  5. Replies
    26
    Views
    4,485

    Turned out nice. You going to do something about...

    Turned out nice. You going to do something about the clutch and throttle cables? That one looks like you could do two bikes with it.
  6. Replies
    9
    Views
    8,666

    Lets see. An electric start inner and outer...

    Lets see. An electric start inner and outer primary, an electric start clutch basket, a starter, shaft/gears/etc. and housing, a solenoid, a starter relay,
    an ass-end bracket for the starter, an...
  7. Nice stance.

    Nice stance.
  8. Replies
    18
    Views
    14,192

    If you are running a stock 74" or 80" and a four...

    If you are running a stock 74" or 80" and a four speed, you will be limited on your gearing depending on your environment. I run an all stock bike and gearing with the exception of the wheel...
  9. Replies
    9
    Views
    1,670

    My stock ('77) wheel is set to the left-side...

    My stock ('77) wheel is set to the left-side based on the fender. I put a 13 spoke mag on the ass-end and it looks offset to the left also. Chain lines up with the tranny and caliper lines up with...
  10. Replies
    2
    Views
    428

    Looks like a run-of-the mill vented cap to me. ...

    Looks like a run-of-the mill vented cap to me. J&P, Dennis Kirk, etc.
  11. This is kinda second hand but worth a read. ...

    This is kinda second hand but worth a read.

    http://www.network54.com/Forum/13357/message/1400197923/I+was+in+a+good+mood
  12. Replies
    5
    Views
    483

    I don't see how throwing a chain would cause a...

    I don't see how throwing a chain would cause a primary noise that wasn't there before you threw the chain. Unless it is the chain, chain guard or something loose on the tranny from getting whipped. ...
  13. Replies
    23
    Views
    1,992

    Some run 1970 chevy nova 6-cylinder 230ci points...

    Some run 1970 chevy nova 6-cylinder 230ci points and condenser. Some run 1972. Take your old set with you as the condensers vary in size and
    some are too large. I'm running car points in my...
  14. Thread: 71' Shov

    by Frog
    Replies
    23
    Views
    3,922

    I'm waiting on the progress pics. Also, that is...

    I'm waiting on the progress pics. Also, that is one damn clean shop area.
  15. Thread: Shovel won't move

    by Frog
    Replies
    5
    Views
    702

    Get your manual out and adjust by the numbers.

    Get your manual out and adjust by the numbers.
  16. Thread: Seat oil tank

    by Frog
    Replies
    2
    Views
    510

    Make the back of the seat one half of your gas...

    Make the back of the seat one half of your gas tank and move your oil to one side of the splits. If you have them. I get hot as hell just sitting on top of my stock oil bag. Comes right up through...
  17. Replies
    9
    Views
    3,159

    Depends on where you live. In Arizona, I run one...

    Depends on where you live. In Arizona, I run one year around. If the temp drops into the forties or fifties overnight I throw a cover on it until the day warms up. I run 60 wgt. in the spring,...
  18. Replies
    6
    Views
    687

    You sure it's the primary drain plug? Everything...

    You sure it's the primary drain plug? Everything kinda runs to that location. Wipe everything clean and eye-ball it really good
    just to make sure. If the plug tightens up, I think you have...
  19. https://answers.yahoo.com/question/index?qid=20101...

    https://answers.yahoo.com/question/index?qid=20101114163913AATRCFI

    Might help . . might not.
  20. You are saying that if you pull the bowl, after...

    You are saying that if you pull the bowl, after the gas has been on, there is no gas in the bowl? Just wanting to make sure we are ont he same page.
  21. For looks go with the Shovelhead. For increased...

    For looks go with the Shovelhead. For increased dependability, go with the Evo. I believe I read somewhere that the '96,'97,'98 were the best but that could be bullshit for all I know. I was...
  22. Make yourself a real jam bar, heat the nut as...

    Make yourself a real jam bar, heat the nut as mentioned/not red hot and a cheater pipe on the breaker bar. Use an impact if you absolutely can't get it with the breaker bar/cheaper pipe scenario. ...
  23. Replies
    13
    Views
    2,631

    Just to confuse you but some interesting reading....

    Just to confuse you but some interesting reading. http://www.hydra-glide.com/phpBB3/viewtopic.php?f=5&t=10590&p=61833&hilit=swingarm+grease+fitting#p61833&mobile=on
  24. Replies
    6
    Views
    818

    Don't confuse the air/fuel mixture screw with the...

    Don't confuse the air/fuel mixture screw with the needle that runs down the middle of the slide. That needle with washers usually comes with a Dyno-jet configuration, f I remember correctly. I...
  25. Replies
    6
    Views
    818

    Air/fuel mix screw? Damn! It has been a long...

    Air/fuel mix screw? Damn! It has been a long time since I had my CV apart. I'll go look to see if it's external but I'm thinking not.

    I looked at mine and thought it was the idle set spring but...
Results 1 to 25 of 49
Page 1 of 2 1 2

Log in

Log in