CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: firstripholdmybeer

Page 1 of 9 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    23
    Views
    1,884

    Thanks for the info guys, HUGE help. I'll get...

    Thanks for the info guys, HUGE help. I'll get after it tonight!
  2. Replies
    23
    Views
    1,884

    Bringing this one back from the grave.... I'm...

    Bringing this one back from the grave....

    I'm wanting to get my rear wheel set tonight and before I remove any links I want to be sure. should I have the axle up front on the axle plate to give...
  3. Dan at BDL says it's normal to not worry about it...

    Dan at BDL says it's normal to not worry about it the small unalignment. luckily I ended up with a extra belt when I got it. hopefully I wont need it but it wont be so hard on the pockets if I do....
  4. LOL Slacker mode engaged light years ago....

    LOL Slacker mode engaged light years ago. :banghead:
  5. Lol sorry for slackin on the first post.

    Lol sorry for slackin on the first post.
  6. I’m going to call BDL and see what they have to...

    I’m going to call BDL and see what they have to say before I buy one. I searched the oem part number and it only came up with EVO, no mention of it fitting a shovel. I also came across a post of...
  7. I have about a 1/4" lip that pokes out of the...

    I have about a 1/4" lip that pokes out of the center of the alternator rotor where the front pulley mount plate hits. this is what's creating the extra room here. maybe there's a different alternator...
  8. 96912 96913 96914

    96912
    96913
    96914
  9. thanks Sky, I reye balled it before, I measured...

    thanks Sky, I reye balled it before, I measured the belt tension and it's closer to 5/8" actually. The trans is hitting the frame post which I'm thinking I'll actually have to move it back slightly...
  10. Front and rear belt sprockets not aligning

    I have a new 1.5" BDL going on a 4 speed ratchet with a cone shovel. I have a straightedge on the sprockets and looks like the basket is inward by about a nickel's width. the tranny is all the way up...
  11. Replies
    1
    Views
    113

    Belt Drives LTD, thanks

    I haven't even run this belt drive clutch I have from BDL... but their customer service is great. I got my setup new from a friend and there were a couple parts missing. I called them up and asked...
  12. I just got one from lowbrow.com that I like a...

    I just got one from lowbrow.com that I like a lot. tc bros has them also.
  13. Hell I know what you're talking about and I...

    Hell I know what you're talking about and I haven't even finished my first HAHA. I had that issue when torquing the rocker box studs and it pulled up. you said the same thing than LOL.

    Great info...
  14. hahaha thanks for that, probably just avoided a...

    hahaha thanks for that, probably just avoided a mess!
  15. Thanks Jim, great info as always. I actually have...

    Thanks Jim, great info as always. I actually have the support already I just wasn't sure if I needed it since I'll be switching to belt.I'm planning to do kick only, here's my setup

    96532
  16. Thanks you so much for this. I'll definitely be...

    Thanks you so much for this. I'll definitely be getting that mounting plate, seems like a great investment. as for the studs, are those specific to that plate? I have all four studs and they seem...
  17. bearing support question and alignment

    Are bearing supports always used, no matter if you're running wet or open belt clutch? my set up is going to be a 1.5" belt in a repop panhead tin and not sure if I need to have that bearing support...
  18. So I ended up with a star hub wheel first and...

    So I ended up with a star hub wheel first and went from there. The midstar hub I got I just sold, after realizing how much of a pain it would be to get parts, spacers, etc. so now I have a 63-66...
  19. sounds god, thanks for the help!

    sounds god, thanks for the help!
  20. Jim, looks like this is a earlier one like you...

    Jim, looks like this is a earlier one like you were saying. measures 1 7/8" inside with a 1 1/2" surface where the pads contact the drum. the shoes measure 1 3/4" wide. so looks like I need a newer 2...
  21. thanks for the "clutches for dummies" as I did...

    thanks for the "clutches for dummies" as I did need it apparently lol. Feathering the clutch should have been a no brainer and I looked past it like an idiot. I'll probably go the jockey shift route,...
  22. HELL YEA! thanks for the link Dragstews!

    HELL YEA! thanks for the link Dragstews!
  23. Hey Jim, thank you. I remember seeing that the...

    Hey Jim, thank you.

    I remember seeing that the earlier juice drum was 1 7/8" and the later ones were 2 1/8" which this one seems to be the later one based on that measurement. also I'm not seeing...
  24. LOL sorry man, I just reread that and yea..very...

    LOL sorry man, I just reread that and yea..very confusing
  25. I was thinking the face plate might be warped,...

    I was thinking the face plate might be warped, but the distance is the same all the way around. the lip of the axle sleeve is level with the lip of the drum, I took a straight edge to it. then...
Results 1 to 25 of 216
Page 1 of 9 1 2 3 4

Log in

Log in