CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: skankr1

Search Forums: Search took 0.01 seconds.

  1. Replies
    1
    Views
    580

    WTB Tiger 650 Head

    Anyone have a 9 bolt single carb head they'd like to part with? It's going on a 71 Tiger motor.
  2. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    The largest center bore from Timkin I could find...

    The largest center bore from Timkin I could find to fit the triumph neck cup was 7/8". I pressed the sporty stem out of the lower tree and turned it down to fit the new bearings.
  3. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    After spending over 20 years in boxes, she...

    After spending over 20 years in boxes, she finally breathes again. I will post some finished pics soon.


    https://youtu.be/w0NnMXEjzQE
  4. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    77149 77150 77151

    77149 77150 77151
  5. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    77145 77146 77152 77148

    77145 77146 77152 77148
  6. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    It's been a little while. Had some computer...

    It's been a little while. Had some computer issues. The bike is mocked up and tore down for frame paint. I'll post some pics.
  7. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75819 75820

    75819 75820
  8. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75817 75818

    75817 75818
  9. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75814 75815 75816

    75814 75815 75816
  10. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    Here's an update. Chain alignment turned out to...

    Here's an update. Chain alignment turned out to be a non issue. I used the smaller engine mount spacers on the left side. I'm not sure if this was how it was mounted from the factory, but it works in...
  11. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    So the frame is square. Neck to axle plates,...

    So the frame is square. Neck to axle plates, lower motor mounts crossed to axle plates, basically any points you choose to measure off of are square. The rear wheel and original spacer have the rear...
  12. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    So I have a question for a sanity check. Right...

    So I have a question for a sanity check. Right now the hardtail is just tacked in. The front hoop is centered, neck is leveled vertically, the lower tubes are leveled horizontally front to back and...
  13. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75394 75395

    75394 75395
  14. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75390 75391 75392 75393

    75390 75391 75392 75393
  15. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75387 75388 75389

    75387 75388 75389
  16. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    75383 75384 75385 75386

    75383 75384 75385 75386
  17. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    Progress. 75379 75380 75381 75382

    Progress.
    75379 75380 75381 75382
  18. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    Thanks for the info Doug. My pops is doing the...

    Thanks for the info Doug. My pops is doing the welding. He's a CWI and used to build drag bike frames. He's knowledgeable and doesn't cut corners. It will be all jigged & TIGed, and we are going to...
  19. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    Update. Cylinders and head are back on. I have...

    Update. Cylinders and head are back on. I have most of the electronic parts (minus battery, ignition switch and wiring) to finish. I just need the hardtail to come in and she'll finally start coming...
  20. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    I did get my tail light built. Repurposed old...

    I did get my tail light built. Repurposed old Turner microphone.

    73122
  21. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    The hardtail is being built. The cylinders and...

    The hardtail is being built. The cylinders and head are at the machine shop getting honed and resurfaced. I haven't done much to it except gather missing parts and wait. I will post more as I...
  22. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    Progress. Started tearing the motor down, got the...

    Progress. Started tearing the motor down, got the rear wheel assembles and bars mounted.

    71884

    71885
  23. Thread: 71 OIF Build

    by skankr1
    Replies
    34
    Views
    6,395

    71 OIF Build

    This is my first post on here. I've owned a basket case Trump for 15 years and finally decided to put it together. The plan is to hardtail it. So far, I have fitted a late 90's sporty front end and...
Results 1 to 23 of 24

Log in

Log in