CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: farmall

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.06 seconds.

  1. Thread: 73 750 🐅

    by farmall
    Replies
    4
    Views
    125

    Vintage drag race Triumphs look great and there...

    Vintage drag race Triumphs look great and there are plenty of frame loops and hardtails floating around. The conversion should be inexpensive.
  2. Replies
    8
    Views
    118

    If not you should be able to make them work. The...

    If not you should be able to make them work. The plating won't be thick so if you happen to hit 'em with solvent then paint they should stay purty longer.
  3. Replies
    8
    Views
    118

    A bit more vibration but I beat lead sinkers into...

    A bit more vibration but I beat lead sinkers into the bar ends of my apes and call it good.
  4. Replies
    14
    Views
    312

    Probe with an incandescent test light everywhere...

    Probe with an incandescent test light everywhere power should be and is until you find where it should be and is not.

    FXRs are quite simple but you need to visualize each SUB-system as Jim...
  5. Replies
    8
    Views
    118

    Thick washers will do the same thing as solid...

    Thick washers will do the same thing as solid bushings for less money.
    Urethane bushings are much stiffer than stock and a considerable improvement over rubber.
    I wouldn't run stock bushings on...
  6. Weld porn is always nice, the closer the better. ...

    Weld porn is always nice, the closer the better.

    Also good to see yer old frame can be straightened by the next owner since that makes it easier to sell.
  7. Replies
    7
    Views
    350

    However because you DID see it, you will never be...

    However because you DID see it, you will never be curious about the outcome of modding a clogbuster with compressed air but without taking proper safety measures (like a low pressure regulator and...
  8. Replies
    2,064
    Views
    664,379

    Good link (not mine) for the factory 1984-1990...

    Good link (not mine) for the factory 1984-1990 FXR service manual. If you own an FXR it is wise to get ALL the books earlier and later. It's 211 megs and a quality scan.
    ...
  9. Replies
    7
    Views
    198

    If ever curious about how a chemical affects a...

    If ever curious about how a chemical affects a surface, test on something expendable and know before using it.
  10. Replies
    2
    Views
    72

    Diesel doesn't injure any of the metals it...

    Diesel doesn't injure any of the metals it contacts in use, therefore it is harmless to chrome.
  11. Replies
    39
    Views
    1,131

    It might be worth applying high temp anti-seize...

    It might be worth applying high temp anti-seize like the nickel-bearing stuff (high temp so it doesn't run) at the top of the shaft where moisture intrusion over many years can cause corrosion and...
  12. Replies
    7
    Views
    350

    Shop project gone wrong.

    I suppose the clogbuster technically did its job....

    https://www.documentingreality.com/forum/f10/rectal-explosion-strange-case-autoerotic-death-214665/
  13. Replies
    10
    Views
    273

    You can hermetically seal an engine or anything...

    You can hermetically seal an engine or anything else that fits using two blue poly drums. I scored a pile of them from a contractor when he recharged our hangar after the foam system fired by...
  14. Replies
    237
    Views
    206,875

    Sticky: Post your SPECIFIC questions and you'll have help...

    Post your SPECIFIC questions and you'll have help aplenty while the responses help others and get many eyes on your questions.
  15. Replies
    4
    Views
    84

    Unless you really want the TSM vs a flasher you...

    Unless you really want the TSM vs a flasher you don't have to use it. They're expensive to replace.

    You can just copy a minimalist harness that does not use one and uses a conventional flasher...
  16. Replies
    24
    Views
    459

    Keep an eye out for steel plate aftermarket 35mm...

    Keep an eye out for steel plate aftermarket 35mm trees too. A used one may be pitted but they can be stripped and painted or coated.
  17. I met one Norton owner who modded a wheelchair...

    I met one Norton owner who modded a wheelchair lift to load his bike into his van. There are a variety of interesting lifts available used. A trailer is much more convenient though since you can work...
  18. Replies
    5
    Views
    227

    The above examples are good ones and building a...

    The above examples are good ones and building a complete roller permits saving the original roller in case the reality of a chopper dream looks worse in reality and OP wants to bolt his engine back...
  19. Replies
    6
    Views
    199

    I don't have an '82 but I do have the factory...

    I don't have an '82 but I do have the factory parts book and apparently the '82s don't use the plastic shaft tube on later models and went for bushings and seals (which suck so it's easy to see why...
  20. Replies
    6
    Views
    261

    Path of least hassle, especially if just building...

    Path of least hassle, especially if just building it to flip because keeping things clean and simple attracts buyers.
  21. Replies
    1
    Views
    113

    Those kits are impressively overpriced for...

    Those kits are impressively overpriced for basically a pleated filter and backing plate. The filter is large enough to not be restrictive and you already own it so unless ya prefer little engine...
  22. Replies
    4
    Views
    328

    Not a bad idea and if they don't hold up you...

    Not a bad idea and if they don't hold up you could use a stainless socket head bolt (use anti-seize for future removal ease) instead.
  23. Replies
    21
    Views
    2,437

    Fuck yeah! Pics of the internals would be...

    Fuck yeah! Pics of the internals would be interesting. That's a clean, slick way to make a custom rigid not suck to ride.

    If you ziptie at the lowest part of the strut with the seat unloaded when...
  24. Mikunis are excellent carbs for Sportsters and...

    Mikunis are excellent carbs for Sportsters and popular on Ironheads from 900cc up so you should be fine. You can drill the intake manifold and press in a VOES tube or if the fit ain't great hit the...
  25. Replies
    42
    Views
    1,821

    The Dyna right brake parts are off the bike at...

    The Dyna right brake parts are off the bike at the moment. Block in pic is the other half of the bar I drilled and tapped. cut in half, trimmed to match the slight frame angle, then welded in place....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in