Search Forums:

Measure the stroke - Top Dead Center to Bottom Dead Center. You need to verify that you still have EL flywheels..

Since you have no history on the motor you may have FL flywheels and not know it.....

Very cool. Military service is an honorable thing. I've always felt good about mine, I'm sure you do as well. My youngest son just got out of the Navy. He was in for 9 years was a sonar tech on...

I was a Tradevman. I worked on simulators as a junior enlisted. I was an instructor after I made E6. I taught basic and advanced ship control and navigation to submarine crews at Sub Base Ballast...

109014

..

109015


..

109016

Quick question -

Does your transmission already have the later main drive gear with the seal or has yours been bored for a seal?

The reason for my question is that most of these old...

I believe in the three P's..

Prostitutes..

Politicians..

Preachers..

All three will fuck you but only one will be honest about it...

Search for posts by -

selectedgrub

69

...

108729

Two years to go.....

Rattlecan Krylon - 1974. Painted this bike in the spare bedroom, house was a rental. I didn't get my deposit back...

108717

108718

69

That invader is for use with a "mid-star (1967-172)" configuration brake. The drum in your picture is for the earlier juice brake with a star hub and will not work with that invader. The mid-star...

“Some people will tell you that slow is good – but I’m here to tell you that fast is better. I’ve always believed this, in spite of the trouble it’s caused me. Being shot out of a cannon will always...

No need to pull the sump plate unless you need to split the cases to service the flywheel assembly.

You can get a gasket here -
...

The Hot Babes thread has been active for 4198 days and has 6077 posts - that's an average of 1.45 posts per day.

The Trump thread has been active for 2013 days and has had 9108 posts - that's an...

Trump is a dogfucker. Fuck him. That is all.

Great info to have. Sounds like you are on the right track here..

Remember that if you use an evo cam you need to run evo lifter blocks and lifters as well.

Good luck with it.

69

You have a good plan there.. It should yield a bike that is fun to ride.

I've attached some info describing the possible 1st, 2nd, and 3rd gear ratios you might see in a Harley 4 speed.. This is...

There was one more after these 4 - we had 5 in 8 years..

My bro and I were both building choppers at the time. Plus I used to build custom sissy bars - 5/8" cold rolled any design for rigid frame. And I helped some other folks with their builds so over a...

Christmas card photo.. Bike is a daily rider 61 FLH with a shovel top end - very common upgrade at the time. I commuted everyday from Lemon Grove to Ballast Point submarine base on this bike. This...

I've been going through a lot of old documents, photos, etc. I found one of my daily notebooks that I carried in a pocket - long before cell phones or computers to organize info.

This notebook has...

I have a couple of questions..

Are you running single fire or dual fire?

When you time the 2Ki does the red LED indicator act as expected and described in the 2Ki instructions?

When you...

If it were my bike with a 74 inch motor I would go with a 49 or a 50 tooth rear wheel sprocket. As you say it is not a big deal to change the sprocket..

I've attached charts for 49 tooth and 50...

Right on the money -

This chart may be helpful - shows RPM in each gear for your gearing - assuming you have the 2.59 first gear..

The A2 that Jim recommends would likely be a good choice.
...

Check this thread - good info..

http://www.chopcult.com/forum/showthread.php?t=55100

Little confusion on what you refer to as your final drive ratio.

Are you saying that you have 24T trans sprocket and a 47T wheel sprocket?

Please provide the info for the primary gearing as...