CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: johnnybarndrunks

Page 1 of 6 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    131
    Views
    33,119

    Where is it it doesn't run good? Low, mid or top...

    Where is it it doesn't run good? Low, mid or top range? Have you checked your plugs at that "spot"?
  2. Replies
    131
    Views
    33,119

    Sorry about the delay man. I run 135 mains, 42...

    Sorry about the delay man.

    I run 135 mains, 42 pilots and 2 nylon shims under each needle (they equal approx 3 steel shims). I had mine ultra sonic washed before reassembling them. I also got a...
  3. Replies
    131
    Views
    33,119

    Hey man. Über sweet ride! Steeldragon is the...

    Hey man.
    Über sweet ride! Steeldragon is the bomb, but if you for some odd reason want to get back to pods, let me know. I've got that exact setup (motor/carbs, yes the keyhole PDs/4-2 pipes/pods)...
  4. 35mm Narrow Glide front end question

    I need to know the diameter of the holes inside the riser rubber bushings in the top tree on the Showa 35mm front end. (Harley FX77-84 amongst others). I'm looking at what with of bolt I can use on a...
  5. Replies
    1,361
    Views
    121,991

    Sticky: I'm a risk assessment engineer and that last...

    I'm a risk assessment engineer and that last picture looks legit. By the book if you ask me.
  6. Replies
    131
    Views
    33,119

    tits. pure tits

    tits. pure tits
  7. Replies
    14
    Views
    2,174

    I might have to get me a pair..

    I might have to get me a pair..
  8. You powder coat those or just cure heat paint in...

    You powder coat those or just cure heat paint in the oven? Either way - I'd get kicked the fuck out if I tried to pull something like that. And yes. It's awesome.
  9. Replies
    45
    Views
    3,243

    Damn Nimrod. your post didn't show until I hit...

    Damn Nimrod. your post didn't show until I hit post.. oh well.
  10. Replies
    45
    Views
    3,243

    CarloFreeze knows his shit for sure. And it's...

    CarloFreeze knows his shit for sure. And it's pretty easy rebuilding carbs once you do it.

    The cycleX setup needs EI and strong compression to be fully operational and they work best on big bore...
  11. This is not my kind of chop - but I can truly...

    This is not my kind of chop - but I can truly appreciate and respect the level of technical capability and your craftsmanship. Truly outstanding work here.
  12. Replies
    15
    Views
    1,025

    Do you get that black liquid from all 4 pipes or...

    Do you get that black liquid from all 4 pipes or just some? (If so wich?)
    The coils are easily tested. Take an ohm-meter and measure the resistance between the primary and secondary lead on each...
  13. Uhm - I can't get that pic to work. Is my pad or...

    Uhm - I can't get that pic to work. Is my pad or is something else wrong?
    If it does what he says, try it. The CB750's are almost bullet proof motors. I would question the 836cc though. Many states...
  14. If they're 12 over you probably need to give 'em...

    If they're 12 over you probably need to give 'em to me. ✌ Looking good here too brotha
  15. Replies
    766
    Views
    64,867

    Yup. @johnny_barndrunks

    Yup. @johnny_barndrunks
  16. Replies
    1,074
    Views
    394,858

    SICK cb man

    SICK cb man
  17. Replies
    17
    Views
    1,316

    Sorry man. The "right way" with those carbs is to...

    Sorry man. The "right way" with those carbs is to put the stock air filter box back on it. Spraying your pods might work, but to get that 100% equal on all four carbs could be difficult. Some have...
  18. Replies
    17
    Views
    1,316

    Yup. The pods. Those carbs are a BITCH to get to...

    Yup. The pods. Those carbs are a BITCH to get to run right with pods. You'll need to restrict air flow in to each carb to begin with. The easiest way would be to mount the stock air box - but like me...
  19. Replies
    1
    Views
    717

    That one was featured in Wrench magazine when...

    That one was featured in Wrench magazine when finished. I'll see if I can dig up the issue when I get back home. For the build thread here I don't know. Can't find it. I may have seen it over at...
  20. Replies
    28
    Views
    3,601

    Lookin good!

    Lookin good!
  21. Replies
    30
    Views
    2,443

    I'd ride it as is

    I'd ride it as is
  22. Replies
    22
    Views
    6,619

    bad. ass.

    bad. ass.
  23. Replies
    79
    Views
    18,468

    You knocked this one out real good. Digg' Oh -...

    You knocked this one out real good. Digg'

    Oh - and a tip on polishing cast/aluminum motor blocks, with the right compounds (only 2 needed) you wont have to sand it past 240 grit. The compound and...
  24. Lookin real sweet dude

    Lookin real sweet dude
  25. Replies
    766
    Views
    64,867

    @johnny_barndrunks

    @johnny_barndrunks
Results 1 to 25 of 127
Page 1 of 6 1 2 3 4

Log in

Log in