CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: DustyDave

Page 1 of 20 1 2 3 4

Search Forums: Search took 0.02 seconds.

  1. Replies
    286
    Views
    13,180

    I know these sites are funny Dragstews but some...

    I know these sites are funny Dragstews but some of the people take them seriously if you don't splain why they are funny.
    Dusty
  2. Replies
    8,753
    Views
    457,056

    You just compared a self entitled, lying, conman,...

    You just compared a self entitled, lying, conman, rapeist, draft dodger to a biker! Kinds makes you ashamed to ride If he's anything like a biker!
  3. Replies
    29
    Views
    1,647

    That bolt might be a little short to chuck...

    That bolt might be a little short to chuck straight, by the time you put a nut on it to keep it spinning with the chuck.
    Dusty
  4. Replies
    34
    Views
    7,595

    Where did you win this shop? When? Dusty

    Where did you win this shop? When?
    Dusty
  5. Replies
    22
    Views
    293

    The only rings i can get anymore for the Cushman...

    The only rings i can get anymore for the Cushman pistons I run in my stroker hardly have enough compression to start and puke oil for 5 o6 hundred mile then suddenly are fine. Don't seem to be very...
  6. Replies
    22
    Views
    293

    If you haven't broke it in get out and break it...

    If you haven't broke it in get out and break it in as the book says. As long as it isn't wet sumping and you keep it full of oil give it a chance to seat the rings.
    Dusty
  7. Replies
    22
    Views
    293

    Perform a leak-down test or at least apply...

    Perform a leak-down test or at least apply compressed air to each cylinder with the piston at top dead center on compression. And listen to where the air leaks. Flat Heads that blow oil out the...
  8. Replies
    21
    Views
    304

    Knowledge without reporting was the crime as he...

    Knowledge without reporting was the crime as he told me. Oklahoma laws tend to be ridiculous! That's why I don't live there anymore. The same city passed a noise ordnance that makes the sound of the...
  9. Replies
    286
    Views
    13,180

    That's sad and really stupid.

    That's sad and really stupid.
  10. Replies
    21
    Views
    304

    In some states it is illegal to even know that a...

    In some states it is illegal to even know that a number was altered or stamped anywhere but the factory. Had a friend spend a small fortune to keep from going to jail for telling an Oklahoma cop that...
  11. Replies
    66
    Views
    1,692

    Lapping on a surface plate, piece of granite or...

    Lapping on a surface plate, piece of granite or even a thick piece of glass with a sheet of wet or dry sandpaper stuck on top is usually successful I even used a tennis court directly on the concrete...
  12. Replies
    9
    Views
    372

    I was dam near run over by a woman driving a mini...

    I was dam near run over by a woman driving a mini van in 2 lanes holding her cell up by the roof so she could see to text in the sun she was driving into with a quart of Old English 800 in the other...
  13. Replies
    29
    Views
    1,647

    Put a bolt and nut through the spacer n chuck it...

    Put a bolt and nut through the spacer n chuck it up in a drill. While its spinning start the cut with the corner of a file, when the grove is where you want it saw it off with a hacksaw. If you...
  14. Replies
    3
    Views
    302

    A small caliper for the hand lever and leave the...

    A small caliper for the hand lever and leave the foot brake alone is a common solution. I like using the Indian Four clutch pedal that latches down. Mountain roads and lots of drunken neighbors make...
  15. Replies
    5
    Views
    204

    Merry Merry Happy Happy Ho Ho n all that shit!...

    Merry Merry Happy Happy Ho Ho n all that shit!
    Dusty
  16. Replies
    19
    Views
    453

    Doesn't matter about the font the boss has been...

    Doesn't matter about the font the boss has been filed down. Don't ride that one anywhere it might be subject to inspection.
    Dusty
  17. Replies
    22
    Views
    669

    I always assumed that the output or power...

    I always assumed that the output or power transistor was going dead short cyclically. But was never interested enough to de-pot and test since a new regulator was always a cure.
    Dusty
  18. Replies
    22
    Views
    669

    The internal regulator that goes in a Toyota...

    The internal regulator that goes in a Toyota forklift alternator or more recently the mini Denso hotrod alternator. Any time I see one cycling like he described after warmup its gonna die soon. Most...
  19. Replies
    22
    Views
    669

    That cyclic fluctuation is the first stage of...

    That cyclic fluctuation is the first stage of regulator failure on the Nippon Denso regulators I use. As the manuals always say substitute a known good part and observe.
    Dusty
  20. Replies
    8
    Views
    841

    A friend built this one bout 8 years ago for one...

    A friend built this one bout 8 years ago for one of his handicapped friends, he couldn't pick up his feet more than a coupla inches, hence the step thru design. VW engine with auto trans, Kawa 600...
  21. Replies
    286
    Views
    13,180

    Isn't it amazing that the vaccine was great and...

    Isn't it amazing that the vaccine was great and gonna save us all when Trump had it developed. And then a Democrat is elected and it's a government conspiracy. Hard to fathom how the facts change...
  22. Replies
    286
    Views
    13,180

    107110

    107110
  23. Replies
    2
    Views
    386

    The other way over the top metal work build was a...

    The other way over the top metal work build was a Knuck http://www.chopcult.com/forum/showthread.php?t=48039 It was more stainless than Selectedgrub but worth revisiting.
    Dusty
  24. Replies
    292
    Views
    11,900

    "I'm gonna figure out a consistent way to get a...

    "I'm gonna figure out a consistent way to get a cast-looking finish on all the permanent mold parts."
    Steel shot in a serious industrial blaster is the old standard. A company that repaints water...
  25. Replies
    12
    Views
    363

    You want the bigger manifold the Trike manifold...

    You want the bigger manifold the Trike manifold and carb were kind of subpar for Meter Maid work much less a bobber. I'll dig through my junk, I think I have one in my swap meet stuff if I didn't...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

Log in

Log in