CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: KG

Page 1 of 7 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    I’ll look into it. Yes it’s 2 phases shorting...

    I’ll look into it.
    Yes it’s 2 phases shorting together.
  2. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    I’m ditching the afr meter and 02 ASAP. Mabey 1...

    I’m ditching the afr meter and 02 ASAP. Mabey 1 more ride to verify readings.
    I soldered n heat shrinked them. I cut enough to offset the splice so they won’t be stacked. Found some other...
  3. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    Think I’m as close as I’m going to get with the...

    Think I’m as close as I’m going to get with the jets. Current 330 mains with the needle clips maxed rich. Had an issue with the charging system. I’m betting it has to do with the extra draw of the...
  4. Replies
    15
    Views
    424

    My buddy was riding his when this happened! I...

    My buddy was riding his when this happened! I would assume a rare case and appears to have been from a loose fastener.
    It bent the shaft and will have to be cut to remove!!!

    I only share...
  5. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    It was a body off resto project I was doing for a...

    It was a body off resto project I was doing for a friend. It cruzing the Mendocino coast now.
  6. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    Working on getting the mikuni vm36s dialed. Got a...

    Working on getting the mikuni vm36s dialed. Got a sync gauge, also ponied up for an afr gauge!
    Though I had I close but apparently not! Pulled carbs for a deep cleaning. Verified 35 pilot jets and...
  7. Thread: China Sucks

    by KG
    Replies
    12
    Views
    554

    “China? They’ve got everything! All the toys!...

    “China? They’ve got everything! All the toys! Everything! I don’t like china toys...” my 7 year old.
  8. Replies
    25
    Views
    630

    I’m saying if your cutting into to the gusset,...

    I’m saying if your cutting into to the gusset, plan to remove the guessers and rebuild. Otherwise stay do your cutting on either side of gusset and slug. But that’s just my 2cents.
  9. Replies
    25
    Views
    630

    They weld wherever there isn’t going to be a...

    They weld wherever there isn’t going to be a gusset directly over it. They set the gusset back so they can weld the tube and gusset at the same time.
    At least that’s what I’ve experienced one the...
  10. Replies
    25
    Views
    630

    If your going in right behind the neck Lillie pic...

    If your going in right behind the neck Lillie pic above, there are sevral layers. The tubes are welded on and the gussets over them. Make sure u re-attach the tubes as well as the gusset.
    That’s...
  11. Thread: Donut Hopper

    by KG
    Replies
    33
    Views
    1,461

    Got the petcock install and ran a pair of fuel...

    Got the petcock install and ran a pair of fuel line to the carb pairs. Need to install inline fuel filters. Think I have the wiring figured out... at least enough to run. Dumped 1/2 a gallon of fuel...
  12. Thread: Donut Hopper

    by KG
    Replies
    33
    Views
    1,461

    Decided to go with a toggle switch instead of key...

    Decided to go with a toggle switch instead of key for now. Just not enough room to fit the big switch in the little box. Roughly wired the ignition to test spark.

    102842

    Cranks over and has...
  13. Thread: Donut Hopper

    by KG
    Replies
    33
    Views
    1,461

    Went to town n grabbed a few things. The agm...

    Went to town n grabbed a few things. The agm batterie is way smaller that the original and give a bit more CCAs.

    102800
  14. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    A couple more pics I dug up. 102739 102740...

    A couple more pics I dug up.

    102739

    102740

    102741

    102742
  15. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    102738 The girder off the bike.

    102738

    The girder off the bike.
  16. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    Thank my buddy took them on a ride last weekend....

    Thank my buddy took them on a ride last weekend. The words are just jibber jabber anyhow!
  17. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    So far so good. Have mabey 1,000 miles on it now....

    So far so good. Have mabey 1,000 miles on it now. Only problem is the jetting n its no biggie if I keep it wound tight! Have more jets coming to.
  18. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    I didn’t have “plans” kinda made it up as I went....

    I didn’t have “plans” kinda made it up as I went. My neighbor offered to take my measurements and put them in his CAD to make templates for upper and lower trees. I still have those...
    I didn’t...
  19. Thread: The “slingshot”

    by KG
    Replies
    17
    Views
    517

    The “slingshot”

    I built this 81 Honda CB750 from the ground up. I had an extensive build thread on another forum but it’s gone belly up.

    So here’s a basic run down.

    I got the stock bike in trade on a 5.0 swap...
  20. Thread: Donut Hopper

    by KG
    Replies
    33
    Views
    1,461

    Never found the petcock I have here somewhere but...

    Never found the petcock I have here somewhere but it’s all good. My buddy Josh brought me some old school chopper gold! A dual outlet pingel petcock! Stoked as this is chopper cool as can be!
    ...
  21. Replies
    13
    Views
    931

    Guess the top hat seals are problematic. They are...

    Guess the top hat seals are problematic. They are xb12 heads set up by NRHS with their valves and seals. I can tell when the stem seals are going as they will let oil sneak by n get a smoke screen on...
  22. Replies
    13
    Views
    931

    Hammer performance told me 96s are notorious for...

    Hammer performance told me 96s are notorious for pulled cylinder studs. “Possibly over torqued from the factory “. Though Ive had a 96 for years and had no issues. Heads come off ever couple years...
  23. Replies
    154
    Views
    21,649

    Wicked!

    Wicked!
  24. Thread: Donut Hopper

    by KG
    Replies
    33
    Views
    1,461

    Took a few days off this project. Getting rolling...

    Took a few days off this project. Getting rolling again...

    Mounted the start switch and a couple fixed holders to the electrical box. Need to pick up a new key switch battery and some electrical...
  25. Replies
    13
    Views
    536

    Chop it! 102384

    Chop it!
    102384
Results 1 to 25 of 156
Page 1 of 7 1 2 3 4

Log in

Log in