CHOP CULT HOME
Email Password
Search

Search Forums:

Type: Posts; User: Mocnyang

Page 1 of 8 1 2 3 4

Search Forums: Search took 0.01 seconds.

  1. Replies
    26
    Views
    4,072

    Thanks for the info guys, I adjusted the pushrod...

    Thanks for the info guys, I adjusted the pushrod a couple times always the same result. I adjusted them when the opposite intake or exhaust valve was full up. That was how I read to do it years ago....
  2. Replies
    26
    Views
    4,072

    So I'm pretty sure I'm going to need to rebuild...

    So I'm pretty sure I'm going to need to rebuild the top end. When I put my hand on the rear exhaust it gets sucked in. Sticky/ stuck valve? Either way I'm going to do the top end
  3. Replies
    26
    Views
    4,072

    If the ignition isn't on neither is the fuel, my...

    If the ignition isn't on neither is the fuel, my thought was that since it wasnt firing right it was whatever unburned fuel was making it past the rings.

    I picked up new intake clamps and orings...
  4. Replies
    26
    Views
    4,072

    So no dice yet, found some new symptoms though....

    So no dice yet, found some new symptoms though. Gas in my oil? What does this mean? The rear runs rich at idle black and sooty plug

    I pulled the pushrods. Reset static time/points gap. Set carb to...
  5. Replies
    26
    Views
    4,072

    Leak down looks good going to ride to work in the...

    Leak down looks good going to ride to work in the morning, when I get there I'll swap wires at coil to see what happens.
  6. Thread: 80" u

    by Mocnyang
    Replies
    320
    Views
    23,875

    Lurking here too! So the sheds, one storage,...

    Lurking here too!

    So the sheds, one storage, other the shop? awsome!
  7. Replies
    44
    Views
    11,005

    I like the look of the fat bobs with the wide...

    I like the look of the fat bobs with the wide glide, but this ^^^^^^^^ is killer. You going to rake the neck at all?
  8. Replies
    14
    Views
    850

    Got a link for those plates? Can you spray...

    Got a link for those plates?

    Can you spray break or carb cleaner on the plates to speed up the process?
  9. Replies
    26
    Views
    4,072

    Next step I guess is a leakdown, I don't have a...

    Next step I guess is a leakdown, I don't have a tester but I just beat the guts out of a old sparkplug, wrapped the threads of a air compressor chuck with aircraft grade rubber tape and screwed it in...
  10. Replies
    26
    Views
    4,072

    I seen those too but there's anot her piece need...

    I seen those too but there's anot her piece need to fill the oring groove.

    Still stumped here, a speed bike runs awsome, plugs look good. At idle rear gets black sooty front normal. I did replace...
  11. Replies
    26
    Views
    4,072

    That's what I thought but the thread I was...

    That's what I thought but the thread I was reading one said they did it everytime the installed it. Haha
  12. Replies
    26
    Views
    4,072

    So went through all the steps again including a...

    So went through all the steps again including a compression test. Cold front and rear 100 hot front 120 rear 115.

    With the bike hot sprayed carb cleaner in all sorts of spots and noticed when I...
  13. Replies
    26
    Views
    4,072

    I'm borrowing a comp tester for the weekend...

    I'm borrowing a comp tester for the weekend hopefully i will be able to get some sort of idea then
  14. Replies
    26
    Views
    4,072

    Points gaps are good within .003 of each other. ...

    Points gaps are good within .003 of each other.

    I wish I had the stuff to check compression and do a leak down. Working in my driveway with basic tools. If I sprayed carb cleaner around the head...
  15. Replies
    26
    Views
    4,072

    Shovelhead rear cylinder not firing right..

    Checked timing, intake leaks, new plugs. Rear plugs black front plugs still silver with a little buildup. Checked pushrods all finger spin with no slop.

    When its cold both cylinders fire good...
  16. Replies
    331
    Views
    479,057

    Sticky: Still have the 66 to 84 clymers?

    Still have the 66 to 84 clymers?
  17. Replies
    461
    Views
    28,821

    Anyone stop by the swap meet in canadaguia, I...

    Anyone stop by the swap meet in canadaguia, I picked up some floorboards and a s&s super b cleaner with element. $55 total
  18. Replies
    35
    Views
    8,441

    I agree with None, the rear looks better on the...

    I agree with None, the rear looks better on the older flh's than the new ones. Might be worth adapting an old fender and struts, or a whole frame swap. I think it would look good with a stripped...
  19. Replies
    29
    Views
    1,375

    Umm this member just posted stating your comment...

    Umm this member just posted stating your comment made him feel stupid for asking a so there's the first example. Didn't have to go far to find it.
  20. Replies
    29
    Views
    1,375

    If your going to keep posting here durantson get...

    If your going to keep posting here durantson get used to these guys trying to make you feel stupid. A bunch of dudes that think their bad ass's, and they know it all when it comes to 2 wheels. So bad...
  21. Replies
    9
    Views
    2,209

    Farmall, do you work on aircraft or something?

    Farmall, do you work on aircraft or something?
  22. Replies
    7
    Views
    1,063

    does the bike not start? And where did you put...

    does the bike not start? And where did you put the red probe? If your trying to figure out why it won't start some info about the bike would help. A schematic would be better. It could be a component...
  23. Replies
    7
    Views
    1,063

    Not sure on how that relay performs but 73 sounds...

    Not sure on how that relay performs but 73 sounds like you reading the coil for the solenoid in side the relay. The solenoid is the part that opens or closes the contacts in the relay.

    73 ohms is...
  24. Replies
    7
    Views
    619

    Also didn't you guys hear? Figure out how to...

    Also didn't you guys hear? Figure out how to build it yourself.
  25. Replies
    20
    Views
    1,644

    I ask the question because I think taking a newer...

    I ask the question because I think taking a newer efi bike and putting a carb on it is stupid.

    Fyi got a 74 flh with a super b and kickstart and I have never owned a bike newer than 77. So carb...
Results 1 to 25 of 181
Page 1 of 8 1 2 3 4

Log in

Log in